Comparison Polk Audio Signa S2 vs Bose Solo 5 TV sound system

The audio format produced by a sound projector is actually the largest number of individual audio channels supported by the device. Note that in this case we are talking about the number of real channels, that is, channels for each of which at least one speaker is allocated; Models that support virtual surround sound can give the listener the impression of more channels than there actually are (see below for more details).

The sound format is indicated by two or three numbers separated by a dot. The first indicates the number of main channels, the second - the number of subwoofers, the third - the number of additional vertical radiators. For example, 2.1 format corresponds to stereo sound (2.0) supplemented by a subwoofer. And the conditional 3.1.2 format includes left, right and center channels, a subwoofer, left and right vertical speakers.

Sound projectors that support a more advanced sound format than 3.1 are designated in our catalog as multi-channel. The classic multichannel audio format is 5.1, but there are other options. In any case, a large number of real channels contributes to the fidelity of the reproduced sound and simplifies setup compared to virtual surround sound systems, but is also more expensive.

The most common sound formats are: 2.0, 2.1, 3.0, 3.1, 4.1, 5.1, 5.1.2, 7.1.

The projector supports the virtual surround function.

The purpose of this feature is that due to special sound settings and the reflection of sound beams from the walls of the room, the listener hears more channels than are actually available in the projector (see "Audio Format"). For example, a 3.1 system with virtual surround sound can produce sound similar to 5.1 surround sound. This allows you to achieve the effect of "immersion" in sound without increasing the number of channels and the cost of the projector. On the other hand, the reliability of such sound is usually noticeably worse than that of real surround sound, and the overall quality is highly dependent on the characteristics of a particular room.

Note that the virtual surround function is specified for 2.0, 2.1, 3.0, 3.1 format systems. In more advanced multi-channel systems, there are a priori additional channels for reproducing surround sound.

The ability of the projector to output a video signal in Ultra HD (4K) resolution — 3840x2160. This is the highest resolution used in modern consumer video equipment — 4 times higher than Full HD. However, note that this feature significantly affects the price of the projector, and to view such a video signal, you will need an appropriate screen. Therefore, it makes sense to specifically look for an UltraHD device only if you initially plan to connect it to a screen of the appropriate resolution.

This feature requires the projector to have at least one HDMI output (see below). In this case, the video signal source can be either an external device or the projector itself, operating in the format of a media centre (for example, a model with direct playback from USB media).

The audio frequency range supported by the projector's speakers.

When evaluating this parameter, it is worth remembering that the audibility range of the human ear is about 16 – 22,000 Hz (and narrows with age). If the projector's frequency range is narrower, this can result in "cutting" low or high frequencies (however, with a slight narrowing, this effect is almost imperceptible). There are models in which the frequency limit is much wider — however, this is a kind of "side effect" of high-quality acoustics and has no meaning other than advertising.

Also note that a wide frequency range in itself does not guarantee high-quality sound — a lot depends on other parameters of the projector.

The presence of a wireless subwoofer in the design of the sound projector.

Any subwoofer enhances the bass response, delivering rich bass. The advantage of a wireless subwoofer is the ability to install it almost anywhere in the room without the hassle of laying wires — this makes it easier to adjust the sound to specific conditions. In addition, such subwoofers can have a fairly solid speaker size — 200 mm or more (see below for more details). However note that wireless acoustics require their own power source and significantly affect the cost of the projector.

Acoustic design of the subwoofer used by the sound projector.

— Closed type. The simplest design option is a speaker installed in a closed case. Such subwoofers have a relatively low volume, but are distinguished by good sound fidelity and a minimum of distortion.

— Bass-reflex type. Subwoofers equipped with a phase inverter - a special tube connecting the inner volume of the case with the outer space. Such equipment improves the volume and saturation of the sound, but increases the likelihood of interference (primarily the rumble of air in the pipe).

— With a passive radiator. The passive radiator is actually a speaker without a coil and a magnet, installed in the subwoofer cabinet along with the main speaker. The purpose of such a radiator is similar to the phase inverter described above, except that it is less susceptible to interference.

The diameter of the speaker in the subwoofer used by the sound projector.

It is believed that the larger the speaker, the louder the sub and the deeper and richer sound it can provide. Models up to 200 mm in size are entry level; This is exactly the size that built-in subwoofers usually have (see above). But free-standing bass speakers can use larger speakers, up to 254 mm (10").

— USB A. In this case, we mean a USB connector that allows you to connect external drives (flash drives, hard drives) to the projector and play content directly from them. At the same time, models with video outputs (see below) can often work as a media centre, outputting the video signal to a TV or other external display.

— mini-Jack (3.5 mm). By itself, the 3.5 mm plug can be used in different types of interfaces; in this case, it means a linear audio input with a mini-Jack socket. This input is mainly used to connect portable audio equipment (players, smartphones) to the sound projector.

— RCA. Technically, RCA (colloquially "tulip") is a type of connector that can be used in different interfaces. However, the term "RCA input" is used to refer only to line inputs for connecting an analogue signal in stereo format. Note that this input consists of two sockets for RCA cables, because. Only one channel of sound can be transmitted through one cable.

— Optical. Connector for digital audio signal connection via TOSLINK fibre optic cable. This interface allows for multi-channel audio transmission and is virtually immune to electrical interference; its disadvantage is the fragility of the cable.

— Coaxial S / P-DIF. A connector for connecting a digital audio signal via an elect...rical cable with an RCA connector (not to be confused with linear RCA, described above). Similar to the optical input described above, in particular, the ability to transmit multi-channel audio through a single connector. At the same time, a coaxial cable, on the one hand, is not so delicate, and on the other hand, it is sensitive to electrical interference (therefore, it is advisable to use a special shielded wire for such a connection).

— Composite. In this case, we do not mean a full-format composite interface of three connectors that allows you to transmit audio and video signals, but only one connector for working with video. And since sound projectors don't display images, the composite input is used to send video through the projector to another device, such as a TV. The composite video interface does not allow working with HD and is not of high quality; on the other hand, it is widespread and can even be used to work with frankly outdated video equipment. Typically this input uses a yellow RCA plug.

— Component. An input designed to receive an analogue video signal for further transmission to another device — a TV, video projector, etc. This connection typically uses three RCA connectors, each carrying a different video component (hence the name). Due to this, the component interface has good bandwidth and picture quality, it allows you to work with HD and is considered the most advanced modern analogue video standard.

— IR control input. Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. Note that the role of the receiver can be played not only by a specialized device, but also by another component of the audio system — for example, an amplifier with an IR control output.

The number of HDMI inputs in the design of the sound projector.

HDMI is the most popular modern interface for working with HD content, it allows you to transmit high-definition video simultaneously with multi-channel audio over a single cable. Having multiple inputs allows you to keep multiple signal sources connected to the projector at the same time and select the source from the remote without fiddling with reconnecting wires.