Capacity
The maximum amount of laundry that can be loaded into the dryer; in other words, the largest weight of laundry that the machine can efficiently process in one cycle.
Capacity is usually indicated by the weight of the dry laundry. Thanks to this, when preparing the laundry for washing, you can immediately assess whether it will fit in the dryer at a time or, on the contrary, you can get by with
a small drying. However, even the most modest modern dryers (and even
slim ones up to 50 cm) in most cases hold
7 kg — this is comparable to loading the drum of a medium-capacity washing machine. And in the most
capacious models, this figure can reach 10 – 11 kg. It is quite enough for domestic and even professional use (for example, in laundromats or laundries of hotels, etc.). However, the typical figures are
drying for 8 kg and
models for 9 kg of laundry. Bigger capacity is relevant for industrial equipment and is not found in consumer-level models.
Also, when choosing, note that in the specs the maximum capacity is usually indicated for linen made of cotton fabric. For other, more voluminous materials, the capacity can be noticeably less — for example, the weight limit for wool products is usually 4-5 times less than for cotton.
Drum volume
The internal volume of the dryer drum.
A
larger drum can accommodate more laundry, but there is no rigid dependence here: models with the same volume may differ in maximum load. It is because to process a large mass of laundry, one need not only a capacious drum but also an engine of appropriate power. At the same time, in a larger drum, the same mass of laundry will dry more efficiently than in a small one, because laundry will be more freely distributed over the drum, crumpled less, and warm air will better penetrate the folds of the fabric. As a result, for the same drum volume, a model with a smaller load will be more efficient and performant than a model with a larger load. On the other hand, a volumetric drum takes up more space and the dimensions of the dryer are largely determined by the dimensions of the drum.
Drum lighting
Lighting system for the internal volume of the device. It usually turns on automatically when the dryer door is opened - thus reducing the likelihood that some items (especially small and dark ones) will be forgotten in the drum.
Drying class
Drying class describes the overall drying efficiency that the machine provides. It is denoted by a Latin letter, where A is the best efficiency, and further in decreasing order (
drying class B is inferior to
class A, but exceeds
class C). Naturally, higher efficiency machines cost more (ceteris paribus).
Controls
The type of control provided in the machine. Almost all modern dryers are equipped with electronic control, so the design of the control panel mainly depends on this parameter. The options here might be:
—
Rotary knob + buttons. The classic option does not lose popularity these days. The rotary knob is usually responsible for selecting the programme and the buttons for controlling additional functions and settings. Such control panels are simple, inexpensive and, at the same time, quite functional. Therefore they are found in all categories of dryers — from low-cost to top.
—
Rotary knob + touch controls. The combination of a rotary knob responsible for selecting the main programme and a set of touch controls that control additional parameters. Compared to the buttons described above, the touch panels have a more stylish and technological appearance; moreover, due to the absence of protruding parts, such a panel almost does not accumulate dirt and is easy to clean. At the same time, these features are generally not fundamental, while the touch controls are somewhat more complicated and expensive than buttons. Therefore, this option is found mainly among dryers of the middle and top classes.
—
Touch controls. This design, on the one hand, gives the device the most accurate and advanced appearance; on the other hand, the control is not as cle
...ar and intuitive as with a handle. Therefore, in its pure form, touch controls are extremely rare — only in high-end dryers.Loading hatch diameter
The diameter of the loading hatch of the dryer. For models with a rectangular hatch (see “Door shape”), in this case, one of the dimensions is indicated — either width or height.
On the one hand, the larger the opening, the more convenient it is to load laundry into the machine, especially large items like bedding. On the other hand, a large hatch requires the appropriate space in front of the device — otherwise, it simply cannot be opened normally. With round openings, everything is quite simple: there should be a place in front of the drying machine corresponding to the diameter of the hatch, plus at least 3-5 centimetres in reserve. If the door is rectangular, this point is not so obvious — manufacturers can indicate the height of the opening, not the width. In such cases, it should be assumed that the door usually occupies almost the entire width of the front of the dryer. Accordingly, normal opening requires free space no less than the total width of the unit.
Door opening
The direction in which the door of the dryer opens.
Most users are right-handed, so from this point of view, the best option is
leftward opening — the free space for loading and unloading laundry is just under the right hand. However, specifically in dryers, the
rightward opening is noticeably more common. It is because such units usually complement washing machines and are most often installed side by side. And in most washers, the door opens just to the left (again, based on convenience for right-handed people). Therefore, it is most convenient to place the dryer on the right and equip it with a hatch that opens to the right — this will allow you to overload the laundry from washer to dryer with minimal effort and time. And vice versa, if the door in the washing machine opens to the right, then it is better to choose a dryer with a leftward opening and install it on the left.
Sometimes both machines are installed as a column — a dryer on top of a washing machine. In such cases, the hatches of both machines should open in one direction — this is more convenient both from the point of view of ergonomics and purely psychologically. Moreover, if the "column” adjoins the wall sideways, then the opening should also occur towards the wall; otherwise, the laundry will have to be loaded and unloaded through the space between the open hatch and the wall, which can be very inconvenient.
...
Note that in some dryers both opening options are claimed. It usually means that the door has a reversible mount, and the direction of opening can be chosen at your discretion. However, this feature does not hurt to clarify before buying.Country of origin
The country in which, according to the manufacturer, the model is manufactured. Despite the fact that most of the capacities are concentrated in
China, European factories (in
Germany,
Poland,
Slovenia,
Turkey, etc.) for the production of household appliances have not gone away. And certain models can be produced there. In general, such a division into a Chinese or European factory should not particularly affect the quality of products, but the stereotype of a reliable European assembly is present in us. However, it is possible that the model may have a country of manufacture, for example, Poland, and in the store under the same article, you will meet China.
