Comparison Sony VPL-CH375 vs Sony VPL-CH370

The lamp model that the projector is designed for. Most projectors come with lamps included, so this information is not needed for normal use. But when looking for a spare lamp or replacement, information about model can be very useful: finding a spare part by the exact name is much easier than by general data like the brand of the projector.

Minimum projector lamp life as stated by the manufacturer. Specified by the total time of continuous operation. Note that if the projector was operated without violations, then upon reaching this time, the lamp will not necessarily fail — on the contrary, it can work for quite a long time. However, when evaluating durability, it is best to focus on the claimed service life.

When working in economy mode, the brightness of the backlight is noticeably reduced, on average by 30-50%. With a decrease in brightness, heat dissipation also decreases, which saves the working life of the illuminator, thereby increasing the lamp life. Thus, the ECO mode allows you to extend the lamp life by an average of 30%. If the typical projector lamp life is 4000 hours, regular use of the ECO mode will extend the backlight life to approximately 5500 hours.

The brightness of the image produced by the projector at maximum backlight brightness. Usually, the average brightness of the screen, derived from a special formula, is indicated. The higher it is, the less the image depends on ambient light: a bright projector can provide a clearly visible image even in daylight, but a dim one will require dimming. On the other hand, increasing brightness reduces contrast and accuracy of colour reproduction.

Accordingly, when choosing this parameter, you need to consider the conditions in which you plan to use the projector. So, for office or school/university use, a brightness of at least 3000 lm is desirable — this allows you to get normal visibility without obscuring the room. In turn, among the top models a very low brightness can be found, because. such projectors are usually installed in rooms specially designed for them with good darkness level. And in ultra-compact devices it is impossible to achieve high brightness for technical reasons.

Detailed recommendations on the optimal brightness for certain conditions can be found in special sources. Here we note that anyway, it is worth choosing according to this indicator with some margin. As mentioned above, as brightness increases, contrast and colour quality decrease, and you may need to use the projector at a reduced brightness to achieve the desired picture quality.

Horizontal frequency supported by the projector.

This parameter is relevant when working with analogue video signal. In such a video, the image is formed line by line: each pixel in the line is highlighted in turn, then the next line is highlighted, and so on. The horizontal frequency describes how many times per second the backlight beam runs from edge to edge of the screen. For normal playback, the projector must support the same refresh rate as the input signal was recorded. However, most models support a fairly wide range of frequencies, and there are no problems with support. Also note that if you are not a professional, then when choosing a projector, it is quite possible to focus on the frame rate (see below) — this parameter is simpler and more intuitive, and support for a certain frame rate automatically means support for the corresponding line rate.

Frame rate, simply put, is the frame rate supported by the projector.

For normal playback, it is highly desirable that the frame rate of the projector match the original frame rate of the video signal. However, most modern models do not support a specific frame rate, but a whole range of frequencies, and quite an extensive one at that.

Note that for viewing most video materials, the range from 24 to 60 fps is quite enough. The exception is 3D content, which may require double the frame rate, up to 120Hz (see " 3D Support " for details).

The projector has a movable lens that can move at least vertically, and in the most advanced models — also horizontally. This feature allows you to adjust the location of the "picture" relative to the screen — most often it is about setting the image exactly in the centre. Using a moving lens for this is much easier than moving the projector or screen itself. Therefore, such models with lens shift can be very useful for those who are not sure that the installation location will optimally match the screen location.

The number of HDMI inputs provided by the projector.

HDMI is a comprehensive digital interface originally designed for high-definition video and multi-channel audio. Today, it is actually a generally accepted standard, outputs of this type are available in the vast majority of HD-enabled video devices — media centers, Blu-ray players, computer graphics cards, etc. The presence of several HDMI inputs allows you to simultaneously connect several signal sources to the projector and switch between them in the projector settings without having to connect and disconnect cables.

Service connectors for connecting control equipment, provided in the design of the projector. Specific control options in each case may be different, they should be specified separately.

— COM(RS-232). A specialized connector, originally used in computer technology. In general, it is considered obsolete, it is relatively rare among computers, but it is very popular in various specialized equipment.

— USB (slave). Connector for connecting to the USB port of a PC or laptop. With this connection, the projector acts as a peripheral device and can be controlled from a computer. In addition, relatively recently, portable projectors have appeared that are designed for wired connection to mobile gadgets such as smartphones or tablets; they also indicate the USB port (slave), although the specific connection may be different (for example, 8-pin in Apple devices).

— LAN (RJ45). Standard connector for wired connection to computer networks. A projector connected in this way works as a network device, it can be accessed (with appropriate settings) from any local computer. This can be more convenient than using only one control computer. In addition, other features can be implemented through the LAN — for example, DLNA (see the relevant paragraph).

— HDBaseT. A complex interface used mainly in professional equipme...nt (see "Main purpose"). In fact, it is an extended version of the LAN described above, it uses the same connectors and cables, but it has more extensive functionality. In addition to LAN and Internet access, HDBaseT provides dedicated control signals, audio and video streaming, and even power up to 100 W.

— 3D Sync. This port allows you to connect a 3D emitter to the projector, which is necessary for the formation of a volumetric image using active 3D technology (see the relevant paragraph). Accordingly, in order to view a stereo image, it is necessary to use active-type 3D glasses. The glasses are synchronized with the 3D emitter, which makes it possible to achieve a clear and understandable stereo image.