Comparison Onkyo C-7030 vs Marantz CD5005

The model of the digital-to-analogue converter (DAC) installed in the CD player.

The DAC is one of the most important components of any modern CD player. It is this module that is responsible for converting digital data recorded on an optical disc into an analogue audio signal that is fed to an external device (amplifier, speakers, etc.). Accordingly, the characteristics and overall quality of the DAC largely determine the sound quality in general. Knowing the DAC model, you can find detailed data on it — characteristics, reviews, test results, etc. — and evaluate how the capabilities of the converter meet your requirements.

Sampling frequency of a digital-to-analogue converter (DAC) installed in a CD player.

A DAC is an indispensable element of any system designed to reproduce digital sound. Such a converter is an electronic module that translates sound information into analogue pulses fed to speakers through amplification stages. The technical features of such a conversion are such that the higher the sampling rate, the better the signal at the output of the DAC, the less it is distorted during conversion. And in the case of CD players, this indicator must also be no lower than the sampling rate of the reproduced digital sound — otherwise the device simply will not be able to "digest" digital data from the media. So, an indicator of 92 – 96 kHz allows you to listen to CD-Audio (sampling frequency 44.1 kHz), but for DVD you need at least 192 kHz. In the most advanced DACs, the sampling rate can be 384 kHz. The latter, however, is rare: in most cases, high frequency is not critical, and such electronics are expensive.

Another indicator that determines the overall quality of the digital-to-analogue audio signal converter. For details on the converter, see "DAC Sampling Rate"; here we note that the bit depth is standardly expressed in bits, and the higher it is, the more accurately the signal at the output of the DAC corresponds to the original signal and the less distortion is introduced into it. In the case of CD players, 24 bits is considered the minimum necessary and at the same time quite sufficient; higher values — 32 bits — are rare, only in premium-level equipment.

The range of audio frequencies that a CD player can reproduce. In general, this parameter determines how full the output bandwidth is, whether too high or too low sound is cut off. However, it is worth noting here that the human ear is able to perceive sound only within the range of 16 – 20,000 Hz (deviations from the upper threshold in different directions are possible, but small, and it decreases with age). All modern CD players cover this range, therefore, in the case of such devices, the sound frequency indicators are reference and practically do not affect the sound. And impressive numbers like 2 – 40,000 Hz, 5 – 60,000 Hz, etc. — this is a kind of "side effect" of the design of a high-quality device; manufacturers use these numbers for marketing purposes, but again, they do not affect sound quality. Also, do not forget that actually audible frequencies are also limited by the characteristics of the speaker system, external amplifier and other equipment connected to the CD player. For example, speakers with a lower frequency range of 150 Hz will “cut off” all lower frequencies, and it doesn’t matter what the lowest bass the player can produce is 16 Hz, 20 Hz or 50 Hz.

The ratio between the level of the useful signal and the level of extraneous noise at the output of the player.

This indicator describes the total amount of extraneous noise (of any origin) that affects the sound quality: the higher the signal-to-noise ratio, the less such noise and the clearer the sound, which is especially important for Hi-Fi and Hi-End systems. The minimum indicator for CD players is 85 – 90 dB, indicators up to 100 dB can be considered good, up to 110 dB — good, more than 110 dB — excellent.

The coefficient of harmonic distortion (harmonics) output by the CD player.

This parameter, along with the signal-to-noise ratio described above, characterizes the overall sound quality of the player. It is calculated by dividing the total sum of harmonics by the value of the main signal at a reproduced sound frequency of 1 kHz, and is expressed as a percentage. Significant levels of harmonics lead to deterioration in sound — from a general feeling of "roughness" and "excessive density" of the sound to the appearance of clearly audible noise; accordingly, the lower the harmonic distortion, the better. In relatively inexpensive CD players, this figure is measured in tenths of a percent, in top models it may not exceed several thousandths of a percent.

The power consumed by the CD player. Usually, unless otherwise noted in the notes, this refers to the power during normal operation. Note that the actual power consumption at a particular point in time may differ from this indicator — for example, when a model with its own power amplifier (see "Built-in amplifier") is operating at low volume or vice versa, when playing a song with sudden volume jumps. However, when organizing the power supply of the audio system, it is necessary to focus on this indicator.

Note that the power consumption cannot be lower than the power of the built-in amplifier (if present, see above). However, some manufacturers may go for tricks — for example, indicate power consumption only in preamplifier mode. As a result, the power consumption stated in the specifications is significantly lower than the actual value when the amplifier is turned on (and sometimes even lower than the rated power of the amplifier alone). In such cases, the actual power consumption can be estimated by adding the claimed power consumption to the power of the amplifier and taking a margin of 20 – 30% for energy losses due to non-perfect efficiency of electronic circuits. For example, for a 50 W model with a 2x60 W amplifier, this value will be about 200 ... 220 W (50 + 2x60 \u003d 170, plus a loss correction).