Comparison Marmorin Sten 3856130 970x510 vs Schock Primus C-200 840х840

The standard way to mount the sink. Some models allow multiple ways to install, at the user’s choice. The specific options may be:

— Mortise overhead. Models fitted in the slot of the worktop in such a way that the side of the sink is significantly above the surface of the worktop. The method of installation is quite simple, but the side raised above the table is in some cases inconvenient.

— Mortise back to back. Models installed in the slot of the worktop so that the side of the sink is at the level of the worktop. Popular due to the ease of installation and convenience in cleaning: if necessary, water and other contaminants can be «driven» by a cloth from the table top directly to the sink. It is true that there is a small gap between the countertop and the sink where pollution can accumulate; but this disadvantage is compensated by the ease of installation.

— Tabletop. Models fixed at the bottom of the countertop - so that the role of the sides actually play the edges of the hole cut under the sink. This method is convenient for maximum convenience in cleaning: from the kitchen table you can easily wipe into the sink spilled liquid or small debris like crumbs, while the contamination will not accumulate in the gap between the sink and the table top (As opposed to butt mounting, see corresponding paragraph. ). At the same time,...the installation of such shells by itself is quite difficult.

— Tabletop module. Quite specific installation method: the sink is installed on the floor top, replacing the table top. For such an installation, it is necessary that the box accurately corresponds to the sink in size, so this option is quite rare.

The number of main bowls provided in the product design.

The simplest variant of the design is 1 main bowl - a traditional, familiar to many variants of kitchen sinks. In addition, models are available with two main bowls - the same or almost the same size. This design provides additional features: for example, one bowl can be filled with soapy water and put dirty dishes there to «decompose» dried dirt, and in the second bowl - rinse dishes that have been in soap solution. On the other hand, it should be borne in mind that sinks on 2 bowls are more cumbersome and expensive than single bowls.

Separately, we note that there are sinks in which the main bowl is supplemented by an auxiliary capacity of much smaller sizes. Such a container is intended for defrosting (see below) and is not the main bowl, so such products in our catalog are one-cup.

Position of the washing bowl relative to the entire body of the product.

The standard, most traditional variants are placement left, right or center (if viewed from the user’s point of view). Some models are available in both left and right layouts; they are marked in our catalogue as «left/right». There are also t. n. reversible sinks: they have a symmetrical shape and can be installed both left-handed and right-handed, at the user’s choice.

The choice for this parameter depends primarily on the layout of the kitchen and how it is necessary to fit the sink.

The presence of a separate additional bowl.

Such a capacity has the form of a small additional bowl (approximately half the main). It can be useful not only for thawing, but also for other tasks - for example, washing fruit or washing pasta through a complete colander (see «Extra»). The convenience of this function is that when using the container - the main bowl remains free and can be used for other purposes: for example, nothing prevents washing the dishes in it.

Availability of space in the sink for the installation of the mixer. This hole can be cut in advance or, if necessary, knocked out during installation (the corresponding place on the model already exists and is made of a softer material).

— Tap. The presence of a tap in the kit will eliminate the search for a suitable style. On the one hand, a tap in a set simplifies the purchase of a sink, but on the other hand, it often introduces certain restrictions. Thus, taps come in different designs and capabilities, as a result of which a complete solution may not satisfy user needs. We also note that this paragraph indicates only those taps that are officially presented in the portfolio of a particular manufacturer of kitchen sinks. Such sets can be assembled within one line or without being tied to a specific series, but purely according to style.

— Colander. The colander supplied with the sink is usually a mesh or hole bottom tray through which water can freely pass. Such a tray can be used in the same way as a common colander - for washing cereals and ready-made pasta, for washing and drying fruit, vegetables and greenery, etc.

Cutting board. Availability of cutting board in the product delivery kit. Such a board, when used, is usually attached directly to the sink; this may be especially relevant in cramped conditions where there is not much space on the kitchen table.

— Automatic valve. Device that facilitates filling the sink with water and draining this water. It consists of the valve itself, which closes the drain opening, and an exit button or lever..., which is installed in a convenient place - for example, near the mixer. To drain water, it is enough to press a button or lever, opening the valve - it is much more convenient and comfortable than to lower your hand in the water and reach the drain hole.

— Mesh on bowl. Mesh made of durable wire mounted over the bowl; can be made removable or foldable. This device is mainly used as a dishwasher; it can be especially useful if the kitchen does not have space for a separate dryer, or if you periodically have to deal with a large number of dishes for which a separate dryer is no longer enough.

— Detergent dispenser. Availability of a dispenser for liquid detergents. This device looks like a container with a characteristic cap and a long spout: when you press the cap, a portion of the contents is delivered through this spout. The size of each portion is very small - by pressing the required number of times, you can quite accurately dose the amount of detergent. Dispensers of this design save space in the kitchen, since most of their body is located under the sink. This affects not only the ease of use of detergents, but also the aesthetic design of the kitchen interior.

— Siphon. The presence of a siphon supply kit is a characteristic curved tube for connecting a sink drain to a sewer. The complete siphon is by definition optimally compatible with the «native» wash; it saves you the hassle of searching and selecting.

There are many national stereotypes: some countries seem more attractive to many users than others. However, in our time these stereotypes are practically grounded. First, in the country of origin of the brand, often only the headquarters of the manufacturer, and the production may be located in another State. Second, the origin from a certain country is not a guarantee of quality: everything depends on how carefully a manufacturer controls its products. Therefore, to assess the quality should be guided not by «nationality», but primarily by the reputation of a particular brand and price category of the product. Among the countries represented are: Germany, Italy, Poland, Romania, Serbia, list", > 3653/href/list."/list/53/pr-36269/">Switzerland, Japan.

The warranty period declared by the manufacturer for this model is the period during which the manufacturer guarantees normal operation. The specific terms of the warranty may vary, however, as a rule, it covers factory defects and malfunctions caused by the fault of the manufacturer/seller and discovered during normal use, without violating the rules.

The longer the warranty period (mostly there are models with a guarantee for 5 years, 10 years, 15 years or even with a lifetime warranty) - the more reliable the sink is, the higher its overall quality, all other things being equal, but the more expensive it will cost in comparison with analogues.

However, depending on the market (country in which it is sold), the warranty for the model may differ. For example, for the countries of the European Union, America and other advanced states, the guarantee can be increased.