Crossover frequency
The frequency of the crossover provided in the speaker design.
The crossover is installed exclusively in the model with several stripes (see "Number of stripes"). This is an electronic filter that separates the incoming audio signal into separate frequency bands and directs each band to its "own" set of speakers. And the crossover frequency shows where the border between these ranges passes. If there are more than two bands, then there will be several similar boundaries: for example, for a four-band system, “0.15 / 0.8 / 2.8 kHz” or “0.12 / 1 / 3.8” may be indicated.
In most cases, this parameter is mainly of reference value: the built-in crossover frequencies are selected according to the performance of the speakers installed in the speaker.
Total rated power
The total rated power of all speaker components, in other words, the sum of the powers of all speakers. As a nominal one, they usually indicate the highest average (rms) power at which acoustics can operate for a long time without overloads and damage. In this case, individual power surges can significantly exceed this value, however, it is the rated power that is the main characteristic of any speaker.
First of all, the sound volume depends on this characteristic: the more powerful the speakers, the louder the sound they can produce if there is a suitable amplifier. In addition, in passive and passive-active models, compatibility with an external amplifier also depends on the power: the output power of the “amplifier” should not exceed the power of the acoustics connected to it, otherwise overloads and even breakdowns are possible.
Detailed recommendations regarding the choice of speakers for power for a particular situation can be found in special sources. However, in general, an indicator of up to
100 W by the standards of modern acoustics is considered quite modest,
100 – 200 W — average,
200 – 300 W — above average, and the most powerful sets give out
up to 500 W or even
more.
In conclusion, we note two more nuances. Firstly, when comparing different systems according to this ch
...aracteristic, one must also take into account the sound format in which they work. In particular, if there is a subwoofer, it can account for a significant part of the total power — up to half or more. As a result, for example, a 2.1 set of 50 W with a 20-watt subwoofer at the main frequencies will not be able to pull out the same volume as a 40-watt 2.0 system: in the first case, each main channel will have only 15 watts, in the second — 20 watts. Secondly, in multichannel systems, the total power can be distributed among the channels in different proportions; so, say, two 5.1 systems with the same total power can differ markedly in front and rear balance at maximum volume.Overall frequency range
The total frequency range that the speaker is capable of reproducing. Specified from the bottom of the range in the lowest frequency component to the top of the range in the highest frequency: for example, in a 2.1 system with main speakers at 100 – 22000 Hz and a subwoofer at 20 – 150 Hz, the total value will be 20 – 22000 Hz.
The wider the frequency range — the fuller the reproduced sound, the lower the likelihood that some part of the low or high frequencies will be "cut off". It is worth noting here that the human ear perceives frequencies on average from 16 Hz to 22 kHz, and from a practical point of view, it makes no sense to provide a wider frequency range in speakers. However, quite a few models go beyond this range, sometimes quite significantly (for example, there are speakers with a range of about 10 – 50,000 Hz). Such characteristics are a kind of "side effect" of high-end acoustics, and they are usually given for advertising purposes.
Thus, the lower limit of the range in modern speakers can be within frequencies
up to 20 Hz, however, higher values \u200b\u200bare more common —
30 – 40 Hz,
40 – 50 Hz, or even
more than 70 Hz. In turn, the upper limit in most modern speakers lies in the range
19 – 22 kHz, although there are deviations both upwards (see above) and
downwards.
Tweeter size
The diameter of the tweeter (speakers) speakers. Since size primarily affects the range of the speaker (as the diameter increases, the operating frequencies decrease), in HF components it can be quite small. More detailed information can be found in special sources.
Woofer size (LF/MF)
The diameter of the woofer or combined woofer/midrange speaker(s). The larger the speaker, the lower its operating frequencies and the more sound power it can provide. Therefore, you should pay special attention to this parameter if you want to get high-quality rich bass - especially if we are talking about an audio system without a subwoofer. More detailed information about speaker sizes can be found in special sources.
Weight
The total weight of all components of the speaker system.
