Comparison Dahua DH-NVR2108HS-S2 vs Hikvision DS-7108HWI-SH

The type primarily determines the type of cameras with which the recorder is compatible.

— Analog DVR. Devices of this type can only work with traditional surveillance cameras that output video in analogue format (usually via a BNC interface, see below). Despite the emergence of more advanced options, such cameras are still very popular due to their simplicity, low cost and reliability of video transmission. The recorder itself may have a LAN network interface and work as a network device, but it is not compatible with IP cameras.

— Digital NVR. NVR type recorders are designed to work with IP cameras connected via a local computer network. These cameras are more advanced than traditional analog cameras and support more advanced features. The main disadvantage of NVR is the rather high load on network equipment when transmitting streaming video; this can lead to interference and failures, especially when there is a large flow of other traffic on the network.

— Hybrid HVR (HDVR). Hybrid devices that combine the capabilities of DVR and NVR and can work with both analog and IP cameras. This expands the possibilities for building surveillance networks, allowing you to combine the advantages of both types of cameras and mutually compensate for the shortcomings. However, such equipment is not cheap.

The number of BNC inputs provided in the design of the registrar.

BNC — connector with bayonet fixation for coaxial cable, used including for transmission of analogue video signal in professional equipment. In registrars, inputs with such connectors are used to connect analogue cameras. The more connectors, the more analogue cameras can be connected directly to the registrar at the same time; and in DVR devices (see "Type"), the number of BNC inputs corresponds to the number of channels.

The number of BNC outputs provided in the design of the registrar.

BNC — connector with bayonet fixation for coaxial cable, used including for transmission of analogue video signal in professional equipment. Outputs with such connectors are designed to transmit a video signal to other components of the surveillance system — for example, monitors.

BNC outputs are found in all types of modern recorders (see above). At the same time, in DVR-type devices, their number, usually, corresponds to the number of BNC inputs, which makes it possible to switch the signal from each camera through its own output. In the NVR, most often only one connector is installed, which is intended for viewing recorded materials, and not images from cameras. The same option is also popular in HVR, although there are also models similar to DVR among them.

The highest resolution in which the recorder can record video when a signal is received from all channels simultaneously. If cameras are not connected to some channels, the recording resolution may be higher (see “Maximum Resolution”).

Higher resolution has a positive effect on detail, but takes up more space and requires more computing power for processing, which accordingly affects the price of the registrar.

The highest frame rate in the recorded video that the recorder can support when recording from all available channels simultaneously. If not all channels are occupied by cameras, this figure may be higher.

The minimum required for comfortable viewing is 24 fps. And in the most modern video standards, the frame rate can be much higher — 50 – 60 fps. Higher values result in better quality and smoother video that allows you to clearly see fast movement; however, such video takes up more space and requires powerful hardware, which affects the price of recorders.

The maximum supported resolution of IP cameras with which the NVR is technically capable of working (primarily recording). With rare exceptions, devices record in maximum resolution from all connected IP cameras. However, the limiting factor here is bandwidth (see the relevant paragraph) – depending on the shooting conditions, it may not be enough.

High resolution allows you to get a more detailed image in which fine details are better visible. On the other hand, such videos take up large amounts of disk space, and their support significantly affects the cost of the device.

The largest total storage capacity with which the recorder is able to work correctly. By default, it is indicated only for internal media with a SATA interface (see above), however, in some models, data is also provided separately for external devices connected via eSATA.

Note that the limit on the total capacity follows from the fact that each individual port has its own limit on the capacity of the drive. In this case, the maximum capacity is distributed equally between the ports. This should be taken into account when choosing drives for the registrar: for example, in a 32 TB model with 8 SATA connectors, the limit for each connector will be 32/8 = 4 TB. This means that installing two internal 8 TB disks in such a registrar will not work, although their total capacity will be less than the maximum.

Support of the registrar of the ONVIF standard.

This standard describes the protocols for the interaction of various components of a video surveillance system; a registrar that supports it will be fully compatible with other ONVIF equipment, regardless of manufacturer.

Recorder compatibility with CMS tools.

CMS is a set of software designed to manage the recorder from a PC. At the same time, the capabilities of this software include not only work with one device, but also the creation of a single video surveillance system from several registrars — so that control and data output from them is carried out through one computer. Anyway, the use of CMS can greatly simplify the work with the registrar.