Comparison AMF VR Racer Shepard vs Special4you ExtremeRace

The highest weight that the chair is guaranteed to withstand with regular use — in other words, the maximum weight of a seated person, allowing you to constantly use the product in normal mode without fear of unexpected breakdown. Note that many models are able to endure short-term excess weight without problems, however, anyway, it is not worth overloading the structure (and even more so doing it all the time): off-design loads will significantly increase its wear, and breakdown can occur at the most unexpected moment.

Chair back height; for models with a variable back height (see "Adjustments"), as a rule, the maximum value is indicated.

The back height is measured from the seat to the top edge. In essence, this is the height of support available to the back. In some situations, you can not pay much attention to this indicator - for example, if the chair is intended for visitors and the role of the back in it is purely symbolic. However, if you have to sit in a chair often and for a long time, this point should also be taken into account. Ideally, it's best to try a few chairs "live" and find out which backrest height is most comfortable for you. If this is not possible, it is worth deciding which area on the body the back should reach (to the shoulder blades, to the base of the neck, etc.) and measure at what height from the seat this area is in a sitting position. And if you need specific support for the back of the head, you should choose among models equipped with head restraints (see above).

Dimensions of the seat installed in the chair in width and depth (from the back to the front edge). For models with variable depth (see "Adjustments"), the maximum value is taken into account when the seat is pushed forward to the stop.

Most modern chairs are designed for the average adult, so paying attention to size is primarily for people of a large, or, conversely, miniature physique. In width, the average is considered to be 45 – 55 cm, the narrowest models are up to 40 cm wide, in the widest it can exceed 60 cm. Similarly, a depth of less than 40 cm is considered small, up to 60 cm — medium, more than 60 cm — large.

Seat height from the floor. The optimal height for a person of average height is considered to be 40 – 50 cm, however, this moment is largely subjective, and the comfort of the chair for a particular user depends heavily on his preferences and physique. Thus, many models have the ability to change the height in a certain range (see "Adjustments"). To choose, it is best to determine “live” at what height you are comfortable sitting, and find a model with the appropriate characteristics.

The height of the armrests installed in the chair relative to the seat. In models that have the ability to adjust the armrests in height (see "Adjustments"), the range of such adjustment is usually indicated.

The overall comfort of using the chair depends on the height of the armrests, but this parameter is largely subjective: even people of the same height can differ in physique and personal preferences. So if comfort is of fundamental importance to you, it is best to check live what armrest height is optimal and choose a chair with the appropriate specifications.

Armrest settings can be quite extensive. In everyday life, there is even a marking 1D, 2D, 3D, 4D, depending on the number of adjustments. The following adjustment options are available: height, length(forward / backward), width(right / left), tilt and swivel(right / left). More about them:

- Height. The ability to adjust the height of the armrests relative to the level of the seat. This feature allows you to adjust the arm rests for maximum comfort and minimize shoulder and neck fatigue.

- Turn (right / left). In this case, the possibility of turning the armrests to the right or left is implied, so that they are not parallel, but “look” in different directions.

— By length (forward / backward). Length adjustment refers to the ability to move the armrests back and forth for the convenience of placing hands under a certain physique of the user of a computer chair.

- By width (right / left). Adjusting the position of the armrests to the right or left in a horizontal plane. The stem adjustment contributes to a comfortable fit and allows you to adjust the chair to a certain arm span.

- By tilt. This adjustment assumes the presence of armrests mounted on swivel mounts. It can work as a height adjustment: turning the armrest in the mount changes not only i...ts inclination, but also the height of the point of contact with the arm. However, the matter is not limited to this: in many models, the handles can be placed vertically (raised or lowered) and, in fact, the armrests can be removed in this way.

If it is assumed that the position of the armrests can only be adjusted in height, they are marked with the designation 1D. For 2D armrests, in addition to the height adjustment, the ability to rotate the palm rests to the right / left (around the axis) is added. 3D armrests are adjustable in height, rotate around the axis and move back and forth. Finally, 4D armrests are considered the most functional - they additionally have the ability to shift the surface of the armrest to the side.

The material from which the base of the chair is made (see "Base construction").

— Plastic. Plastic is notable for its low cost, combined with ease of processing — it can be easily given even a rather complex shape. This material is considered less durable than metal, but modern plastics are able to provide sufficient strength even for chairs designed for high loads (see "Maximum user weight"). However this is true only for bases of the "cross" type; for the legs and skids, the plastic is still not strong enough. However, it is found in models of all price categories.

— Metal. The main advantage of the metal is its high strength, due to which it can be used for all types of bases. At the same time, it is somewhat more expensive than plastic, and therefore, among armchairs with a cross, it is found mainly in models of the middle and higher levels.

— Tree. Wood can be attributed to design materials: it is used not so much for practical reasons as to provide the chair with a stylish and aesthetic appearance. At the same time, it is considered more reliable than plastic (although not as reliable as metal), so it can even be used for skids. However chairs with wooden bases are quite expensive.