Comparison TOPEX 74L231 vs FUBAG N90

General purpose of the instrument.

A construction stapler in the original sense of the word is called a staple gun — a tool designed to work exclusively with staples. For driving nails, in turn, nailers are used, while in such devices the matter may not be limited to nails alone. However, the most versatile are the combined models — 2-in-1 and 3-in-1 staplers. Here is a more detailed description of all these varieties:

— Stapler. Stapling tools that are not intended for use with other types of fasteners. One of the most popular areas of application for such devices is furniture production and other activities where it is necessary to sheathe various structures with fabric, mesh, etc.; although, of course, the matter is not limited to this. Anyway, staplers are not as versatile as 2-in-1 and 3-in-1 models, but at the same cost, a highly specialized tool usually turns out to be more performant, practical and reliable than a combination device.

— Nayler. He's also a "nail gun". Tools similar to staplers, but designed to work with nails (sometimes also with pins / studs) and do not involve the use of staples. For a number of reasons, pneumatic nailers are most widely used nowadays, but there are other variations.

— Stapler (2-in-1). Devices that can work with both staples and nails; in other words, a combination of a traditional stapler and...a nailer in one tool. The main advantage of such models is versatility: a combined tool can replace two specialized ones at once. At the same time, it will cost significantly less than two separate devices, and it will take up less space; and to switch between different types of fasteners in many models, you don’t even need to change the store — just load the desired type of consumables into it. However, if you plan to work with only one type of fastener, you should not buy a combined device so as not to overpay for unnecessary functionality.

— Stapler (3 in 1). Tools from this category are capable of working with staples and nails, as well as with pins (studs). Thus, such models are generally similar to 2 in 1 devices, but they have even more extensive functionality and, accordingly, are somewhat more expensive.

— Nail. Traditional nails are pointed rods with hats. However, hammers are often made for specific types of nails, and ordinary ones cannot be charged in them, this point in each case must be clarified separately. The nail is usually hammered in as a whole, right up to the head; such fasteners are tightly held in the material.

— Staple. Colloquially, staples are sometimes referred to as "paper clips", although this is not entirely true. Such fasteners are familiar to many from ordinary stationery staplers, however, staples can also be used for more serious tasks — for example, attaching upholstery to wooden furniture. They do not hold as tightly as nails, but the oblong shape of the staple is in some cases a decisive advantage, and reliability is often enough.

— Pin / hairpin. Fasteners that are driven in the same way as nails, but do not have expanded hats at the top. In addition, they differ somewhat in application: the pin can protrude above the surface of the material, or vice versa, be completely hidden inside, in such a way that then “mask” the fasteners with putty, decorative film, etc. All this requires specific design features, so not every stapler capable of using nails will be compatible with pins / studs.

Staple models that the tool is compatible with.

Usually, quite specific options are indicated in this paragraph, so finding compatible consumables is not difficult. The specific dimensions of the fasteners should be specified according to the manufacturer's data — different brands use different markings.

Air pressure for which the pneumatic nailer/stapler is designed (see "Type"). It is this pressure that the compressor to which the tool is connected should give out: if the pressure is too low, the efficiency will noticeably drop, and if it is too high, it can lead to breakage and even injury.

The angle at which the magazine is set in the tool. Note that in this case, the angle is measured relative to the perpendicular to the body, more precisely, to the direction of the “shooting” of the fastener; in other words, if the angle of inclination is 0 °, this means that the store is strictly perpendicular to the body. This makes quite a practical sense: an inclined magazine makes it easier to work in hard-to-reach places, driving fasteners at an angle and some other specific tasks, and the greater the deviation of the magazine from the perpendicular, the more pronounced these advantages. At the same time, the real need for such a design is not always required, so many staplers (especially entry-level ones) have a perpendicular magazine, and in such cases the angle of inclination (0 °) is not indicated at all.

Also note that fasteners (especially branded ones, for a tool of a certain brand) can be sold in packs designed for a specific store angle; in such packs, the parts themselves are connected with a slope corresponding to this angle.

The number of fasteners that fit in the stapler magazine.

Note that manufacturers tend to indicate the maximum number of parts in the characteristics — that is, the capacity for the thinnest fasteners allowed by the design of the tool. Accordingly, fewer larger parts will fit in the store; this must be taken into account when choosing. Nevertheless, this parameter makes it possible to evaluate the instrument and compare models similar in class to each other.

Large capacity, on the one hand, allows you to work longer without interruptions to recharge the stapler. On the other hand, volume magazines are usually very bulky and can weigh a lot on their own, not to mention the weight of the fasteners loaded in them. Also, if parts are charged one at a time, recharging can become quite a long and tedious affair. Therefore, it makes sense to specifically look for a tool for 100 parts or more(especially when it comes to thick fasteners) only if the ability to work for a long time without reloading is more important than the disadvantages described above.

The largest width of staples (see Fastener Type) that the stapler can work with.

The width of the bracket is, roughly speaking, the distance between its legs. Different situations and types of work require different sizes of staples, and sometimes the width must be quite large. However, a staple that is too large simply will not fit into the store, not to mention the fact that the stapler can “shoot” it normally. Therefore, this limit cannot be exceeded, and if you plan to work with brackets, you should pay special attention to the maximum width when choosing.

The smallest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. Small staples do not require much power to drive, but the tool may not be designed for fasteners that are too short due to other parameters — for example, the design of the magazine. Therefore, for many models, this limitation is quite relevant, and in powerful professional models, the minimum length can be quite large — more than 20 mm.

The largest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. This means that working with staples of great length requires not only the appropriate design of the magazine and the feed mechanism — the stapler must also be quite powerful in order to provide the effort necessary for effective clogging. And this, in turn, affects the dimensions, weight and price of the tool. In fact, this means that it does not always make sense to specifically look for a model that can work with long staples — you need to evaluate the specifics of the intended work: often the best choice is a relatively “short”, but at the same time inexpensive and compact tool.

In general, a limit of 10 – 15 mm is typical for entry-level staplers, and in professional models this parameter can exceed 50 mm.