USA
Catalog   /   Home & Renovation   /   Bathroom & Taps   /   Kitchen Sinks & Accessories   /   Kitchen Sinks

Comparison Zigmund&Shtain INTEGRA 500 543x456 vs Blanco Subline Level 700-U 518393 730x460

Add to comparison
Zigmund&Shtain INTEGRA 500 543x456
Blanco Subline Level 700-U 518393 730x460
Zigmund&Shtain INTEGRA 500 543x456Blanco Subline Level 700-U 518393 730x460
Outdated Product
from $1,105.10 
Outdated Product
TOP sellers
Main
Extra layer for temporary storage and drying.
Mount type
tabletop
tabletop
Materialgranite composite
granite composite /Silgranit/
Shaperectangularrectangular
Working surface
Main bowls1
Bowl locationleft
Additional bowl
Overflow?
General
Minimum cabinet width (base)600 mm800 mm
Working surface size543x456 mm730x460 mm
Main bowl size (LxWxD)500x396x200 mm700x400x200 mm
Additional bowl size (LxWxD)190х400х140 mm
Country of originGermany
Manufacturer's warranty5 years
Added to E-Catalogdecember 2015february 2014

Main bowls

The number of main bowls provided in the product design.

The simplest variant of the design is 1 main bowl - a traditional, familiar to many variants of kitchen sinks. In addition, models are available with two main bowls - the same or almost the same size. This design provides additional features: for example, one bowl can be filled with soapy water and put dirty dishes there to «decompose» dried dirt, and in the second bowl - rinse dishes that have been in soap solution. On the other hand, it should be borne in mind that sinks on 2 bowls are more cumbersome and expensive than single bowls.

Separately, we note that there are sinks in which the main bowl is supplemented by an auxiliary capacity of much smaller sizes. Such a container is intended for defrosting (see below) and is not the main bowl, so such products in our catalog are one-cup.

Bowl location

Position of the washing bowl relative to the entire body of the product.

The standard, most traditional variants are placement left, right or center (if viewed from the user’s point of view). Some models are available in both left and right layouts; they are marked in our catalogue as «left/right». There are also t. n. reversible sinks: they have a symmetrical shape and can be installed both left-handed and right-handed, at the user’s choice.

The choice for this parameter depends primarily on the layout of the kitchen and how it is necessary to fit the sink.

Additional bowl

The presence of a separate additional bowl.

Such a capacity has the form of a small additional bowl (approximately half the main). It can be useful not only for thawing, but also for other tasks - for example, washing fruit or washing pasta through a complete colander (see «Extra»). The convenience of this function is that when using the container - the main bowl remains free and can be used for other purposes: for example, nothing prevents washing the dishes in it.

Overflow

Overflow has the form of an opening located at the top of the bowl; this opening must be connected to the drain by a hose. Such a device avoids the transfusion of water over the edge of the sink: when the bowl overflows, water will flow into the sewer through the overflow and will not rise above the edges.

Minimum cabinet width (base)

The smallest width of the cabinet, pedestal or other base required for the installation of the sink. By width in this case means the distance between the side walls of the cabinet (base). If the width of the sink is too small, it will not get the necessary support, and its normal use will be impossible.
Main minimum dimensions: >less than 45 cm, 45 cm, 50 cm, 60 cm, 80 cm, more than 80 cm.

Country of origin

There are many national stereotypes: some countries seem more attractive to many users than others. However, in our time these stereotypes are practically grounded. First, in the country of origin of the brand, often only the headquarters of the manufacturer, and the production may be located in another State. Second, the origin from a certain country is not a guarantee of quality: everything depends on how carefully a manufacturer controls its products. Therefore, to assess the quality should be guided not by «nationality», but primarily by the reputation of a particular brand and price category of the product. Among the countries represented are: Germany, Italy, Poland, Romania, Serbia, list", > 3653/href/list."/list/53/pr-36269/">Switzerland, Japan.

Manufacturer's warranty

The warranty period declared by the manufacturer for this model is the period during which the manufacturer guarantees normal operation. The specific terms of the warranty may vary, however, as a rule, it covers factory defects and malfunctions caused by the fault of the manufacturer/seller and discovered during normal use, without violating the rules.

The longer the warranty period (mostly there are models with a guarantee for 5 years, 10 years, 15 years or even with a lifetime warranty) - the more reliable the sink is, the higher its overall quality, all other things being equal, but the more expensive it will cost in comparison with analogues.

However, depending on the market (country in which it is sold), the warranty for the model may differ. For example, for the countries of the European Union, America and other advanced states, the guarantee can be increased.