Comparison Accuphase A-250 vs Accuphase M-6200

The total capacitance of the capacitors installed in the power supply of the amplifier. Usually, for ordinary lovers of high-quality sound, this indicator is not practically significant: the capacitance is selected in such a way as to optimally (or at least minimally) match the characteristics of the amplifier. However, for demanding audiophiles who pay attention to the smallest details of audio system components, capacitors are also often of interest.

The fact is that they are an important part of the rectifier circuit — they smooth out current fluctuations that arise both due to the imperfection of the rectifiers themselves and due to various external factors. Knowing the total capacitance of the capacitors, one can also evaluate the efficiency of their work: the higher this indicator, the more stable the power supply will work and the lower the likelihood of sound distortion due to its fault. There are special formulas that allow you to derive the optimal capacitance of capacitors depending on the type, power and other parameters of the amplifier; they can be found in specialized sources.

The nominal sound power output by the amplifier per channel when operating with a load having a dynamic resistance (impedance) of 8 ohms. In our catalog, this parameter is indicated for the mode when all channels of the amplifier work under load (see "Number of channels"); in the presence of unused channels, the rated power may be slightly higher, but this mode cannot be called standard.

Rated power can be simply described as the highest output signal power at which the amplifier is able to work stably for a long time (at least an hour) without negative consequences. These are average figures, because in fact, the audio signal is by definition unstable, and individual level jumps can significantly exceed the rated power. However, it is she who is the main basis for assessing the overall loudness of the sound.

This indicator also determines which speakers can be connected to the amplifier: their rated power should not be lower than that of the amplifier.

According to the laws of electrodynamics, with different dynamic load resistance, the output power of the amplifier will also be different. In modern speakers, the standard values \u200b\u200bare 8, 6, 4 and 2 Ohms, and power levels are indicated for them.

The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 4 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.

The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 2 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.

This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.

As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the balanced XLR input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the RCA line input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

— Preamplifier (Pre-Amp). The presence in the design of the device of a separate output for the signal from the preamplifier. In the type of amplifiers of the same name (see "Type"), such an output is available by definition and is the main, and sometimes the only one. On integrated models (see ibid.) , the Pre-Amp output allows you to connect an external power amplifier and use it instead of the internal one. This feature can be useful, for example, to connect a more powerful speaker instead of the original one, or to work in Bi-amping mode. It is worth noting that the Pre-Amp output can also be installed in power amplifiers, playing the role of a "splitter".

— Subwoofer. The presence in the amplifier design of a separate subwoofer output. Usually, such an output uses an RCA connector (see "Input to the amplifier (Main)"), and the function itself is implemented through a crossover, which selects the low-frequency range in the signal and redirects it to a subwoofer. The "own" output makes it much easier to connect a subwoofer : it does not require any additional equipment, the amplifier itself is enough. This usually provides for the possibility of working with any type of subwoofer — both passive and active; however, in the first case, you will need an additional external amplifier.

— Coaxial S/P-DIF. The presence in the design of the amplifier of the S / P-DIF output of an electric typ...e, with signal transmission via a coaxial cable. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Optical. The presence in the design of the amplifier output for transmitting a digital audio signal over a fiber optic cable TOSLINK. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Jack (6.35 mm). Presence of TRS type outputs in the design of the amplifier. These outputs are jacks for 6.35 mm Jack plugs and may look like the corresponding headphone jack (see below). However, this similarity is misleading: TRS produce sound on the principle of "one channel per plug" (an exception may be information amplifiers). This type of Jack connector is found mainly in high-end professional amplifiers.

— Speakon. An interface used in professional audio equipment to connect acoustics to a power amplifier. It has become widespread in high power equipment, including concert amplifiers (see "Intended Use"), due to its increased reliability and suitability even for working with very powerful audio signals. But in household appliances it is rarely used.

— Control output (IR). The control output allows the amplifier's built-in IR receiver to be used to control other components in the audio system, such as a DVD player in another room, out of range of the remote control, from the remote control. With this scheme of operation, the amplifier actually plays the role of a remote sensor, receiving commands and transmitting them through the control output to another device. Note that the very presence of such inputs and outputs does not guarantee the compatibility of various devices, especially if they are produced by different manufacturers; Sharing details should be clarified in the official documentation.

The number of REC outputs in the design of the amplifier. This output is a kind of line interface designed to output sound to a recording device; one of its features is a constant signal level. Since RCA connectors are usually used for connection (see “Amplifier Input (Main)”), a pair of connectors is counted as one REC output — this is the only way to ensure stereo sound transmission.