Comparison Crosman 1911BBb vs BORNER CLT125

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The type of ammunition that the pistol/revolver is designed for.

Pneumatics can use balls or lead bullets, and some models are compatible with both varieties at once. In weapons chambered for Flaubert and a blank cartridge, the type of ammunition is already obvious from the name. Here is a more detailed description of each option:

— Balloons. Ordinary round balls; for traditional 4.5 mm pneumatics they are made of metal, for airsoft guns of 6 mm caliber they are made of plastic (although other materials are occasionally found). Actually, the airsoft "weapon" by definition uses only balls, it is not made for other types of charges. As for classical pneumatics, here the main advantage of this option can be called a low cost — balls are somewhere much cheaper than lead bullets. In addition, they have good penetrating power, and magazines and reloading systems for balls are extremely simple. On the other hand, such ammunition is less suitable for accurate long-range shooting. Firstly, balls are inferior to bullets in terms of ballistic characteristics; secondly, they are usually made of hard steel and are practically unsuitable for working with rifled barrels. On the other hand, for recreational shooting and simple training at a relatively short range, these points are not critical; so it is this type of ammunition that is most common in modern air pistols.

— Lead bullets. A bu...llet in this case is called a projectile of a directional shape, with a clearly defined front and rear. The specific form of such projectiles may be different, but they all have a number of common features. So, any bullet at the same initial speed flies further and hits more accurately than a ball. And the material is usually lead or another soft metal, which provides a number of advantages. Firstly, bullets work great with rifled barrels: the edges of the bullet clearly fit into the grooves on the inner surface (many bullets are even able to expand slightly at the time of the shot, for the tightest possible fit in the barrel), the projectile is effectively untwisted and stabilized, while the rifling is worn minimal. Secondly, bullets flatten out when they hit a more or less hard surface — this minimizes the risk of ricochets. At the same time, bullets are more expensive than balls, and in multi-shot models, they require a more complex design of magazines and reloading mechanisms. As a result, this type of ammunition is relatively rare in short-barreled pneumatics — mainly in professional long-range pistols, as well as in models where this is due to design features (in particular, bullets are better suited for spring-piston “breaks”).

— Balls / lead bullets. The ability to use both types of ammunition described above at once, to choose from. Note that such versatility can be implemented in different ways: some pistols / revolvers are indeed universal in terms of the type of ammunition (unless each variety needs its own magazine), others are produced in two separate versions — for bullets and for balls. This point should be clarified separately before buying. It is also worth considering that in "omnivorous" weapons with a rifled barrel, it is better to use bullets if possible, and balls should be considered as a fallback. This is due to the fact that the balls are poorly compatible with such weapons; see "Barrel" for details.

— Flaubert's cartridge. Small-caliber (4 mm) cartridge, which is actually a primer with a bullet, without a powder sample (or with a very small amount of gunpowder — in the form of a few grains). In fact, it is a firearm, however, in terms of ballistic characteristics, a weapon chambered in Flaubert is comparable to pneumatics, due to which in many countries it is officially equated to pneumatic and sold without special permits (however, this point needs to be specified separately). Note that the vast majority of weapons chambered for this cartridge are revolvers; pistols are rare and have a specific design (for more details, see "Form Factor").

— Blank cartridge. A cartridge with a case, a primer and a powder charge, similar in design to a full-fledged firearm, except that it does not contain a bullet. Instead, the case mouth is crimped in the form of an "asterisk" or covered with a plug made of an easily destructible material like plastic. Note that such cartridges can be used not only in specialized “weapons” (see “Type”), but also in most traumatic and combat pistols of the corresponding caliber; however, blank pistols usually do not require special permits, and anyone can practice basic skills with them (including working with recoil and reaction to a shot).

The number of shots on one gas station that an air pistol or revolver is capable of producing. Specified for gas models and PCP (see "Type"); in the first case, the data is usually given for a standard 12-gram cartridge with carbon dioxide, in the second case, for a full filling of the built-in reservoir.

Note that this parameter is quite approximate, since the actual number of shots at a gas station may differ slightly from the claimed one. Nevertheless, according to the claimed number of shots at a gas station, it is quite possible to evaluate different models of pneumatics and compare them with each other. However it must also be taken into account that the last portions of gas / air pressure is noticeably reduced — and this reduces the initial velocity of the bullet and the firing range, and can also lead to problems in the operation of blow-back systems (see below). So if the number of shots from one gas station is important for you, you should proceed from the fact that the number of “effective” shots (with full bullet speed) will be somewhere 10-15% less than the maximum claimed.

The presence in the pistol of the Blow-back system — a mechanism that simulates the operation of automation and the recoil of a real weapon. Note that blow-back models are found only among air pistols; in weapons chambered for Flaubert (see “Type”), such systems are not applicable due to the extremely low energy of the ammunition, and for pistols chambered for a blank cartridge, the term “Blow-back” itself is not relevant — they already use full-fledged automation, the same as in firearms.

This feature enhances the resemblance of an air pistol to a real firearm: with each shot, the casing-bolt moves back and forth, creating a characteristic recoil with a barrel toss. The second important nuance is that the blow-back actuation cocks the trigger, reducing the force on the trigger — and this, in turn, makes it easier to control the weapon and contributes to increased accuracy. And in many models with such systems, a full-fledged slide lag is also provided: when the cartridges run out, the casing-bolt is fixed in the rear position, and to continue shooting, you need not only to change the store, but also remove the weapon from the delay. Many amateur shooters appreciate blow-back pistols solely for their general resemblance to combat counterparts, but this feature also has a very practical meaning: it allows you to develop useful skills in working with recoil and reloading weapons. On the other hand, note that gas is additionally cons...umed for the operation of automation; and the muzzle velocity in such pistols is lower than in similar models without blow-back.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

The material from which the body of the gun is made.

The main materials found nowadays are metal and plastic. At the same time, the division into metal and plastic cases is actually relevant only for pneumatics; models for "flobert" and for a blank cartridge (see "Type") are almost all made of metal. As for the features of each of the materials, they are as follows:

— Metal. The key advantages of metal are strength, reliability and similarity to materials used in firearms. Such cases weigh much more than plastic ones, but this moment is also often referred to as an advantage — it further enhances the resemblance to combat pistols / revolvers, creates a sense of solidity and allows you to effectively practice skills in working with weapons. The main disadvantage of metal is its rather high cost. In addition, note that the composition of this material may be different: in particular, in low-cost models, a lighter and cheaper, but less durable silumin or other similar alloy can be used instead of steel.
Separately, it should be said that in some modern firearms (in particular, Glock) only the casing-bolt is made of metal, and the frame and handle are made of plastic. For air pistols and starting pistols made of similar materials, our catalog also lists metal as the body material in order to emphasize the similarity with combat prototypes.

— Plastic. Material used mainly...in low-cost models of pneumatics. In this case, it means a body made entirely of plastic — including a casing-shutter, if available in the design. The main advantage of this material in this case is its low cost — this determined the specifics of its application. On the other hand, plastic is noticeably inferior to metal in terms of strength and reliability, and the small weight of such cases is considered by many to be a disadvantage — the weapon is perceived as a "toy". However there are also advanced varieties of plastic — durable, heat-resistant, suitable even for military weapons; however, in pneumatics, such materials are used in rather expensive copies of real pistols, where a plastic frame is combined with a metal casing-bolt — and such cases are already considered metal (see above).

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).