Comparison Crosman 1720T vs Hatsan AT-P2

The working length of the barrel installed in the pistol / revolver is from the chamber to the muzzle. In airsoft models (primarily AEGs, see "Type"), the length of the inner barrel is indicated, along which the bullet directly moves. Three main points directly depend on this parameter: the initial velocity of the bullet, the length of the aiming line and the dimensions of the weapon.

In short-barreled (up to 20 – 25 cm) pneumatics and Flaubert's revolvers, a long barrel allows you to achieve higher initial speeds. However there is no rigid dependence here, and models with the same barrel sizes can differ markedly in initial speed (especially since the latter also depends on a number of parameters, primarily the principle of operation — see "Type"). However, long-barreled pistols are generally better for long-range shooting than short-barreled pistols. This is due to the second nuance — the length of the sighting line: a long barrel allows you to increase the distance between the front sight and the whole, thereby reducing errors in aiming. However, with regard to dimensions, the increase in the length of the barrel not only makes the weapon more cumbersome, but also worsens its balance, since the centre of gravity shifts forward because of this.

There are a couple more nuances associated with this indicator. So, in copies of combat pistols (see above), the barrel length is selected in accordance with the size of the weapon from which this model wa...s copied. And for products chambered for a blank cartridge (see "Type"), this parameter is not indicated at all, since there is virtually no full-fledged barrel in such pistols.

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The number of charges that fit in the weapon.

According to this parameter, weapons are divided into single-shot and multi-shot. However, this division is relevant only for pneumatics in the pistol form factor — it can be either multi-shot or single-shot. All models chambered for Flaubert and starting pistols (see "Type") are made multi-shot, revolvers are also multiply-shot by definition (see "Form factor").

The advantages of a multi-shot design as a whole are obvious: it allows you to fire several shots without being distracted by the replenishment of ammunition. At the same time, the reloading systems in air pistols and other similar weapons are quite simple and do not particularly affect the final cost of the design. Therefore, a single-shot design is rarely found nowadays, and mainly in those pistols where it is indispensable due to design features — in particular, in spring-piston models with a broken barrel.

The capacity of the magazine provided with the pistol, or the drum installed in the revolver (see "Form factor"). For obvious reasons, it is indicated only for multiply charged models (see "Charging capacity").

Repeatingly charged air pistols / revolvers are conditionally divided into models with magazines up to 15 charges and more than 15 charges. The largest capacity here is airsoft AEGs (see "Type"), copying submachine guns — they are not uncommon in stores for 50 balls or more, and as additional accessories for many models, so-called "bunkers" are produced, where the number there are already hundreds of charges. As for traditional pneumatics, it is worth noting that if the pistol is designed for bullets and balls at the same time (see "Type of ammunition"), then the capacity when using different types of charge may vary — usually, it is higher for balls in such cases, and this figure and indicated in the characteristics as the main one.

As for the weapon chambered for Flaubert, in it the “classic of the genre” is a revolver with a drum for 9, less often for 8 rounds. A greater number of charges is not found — for this the drum would have to be made too bulky; a smaller number — about 5 – 6 rounds — can be found in individual revolvers, as well as models in the form factor of a pistol, where the dimensions of the case do not allow you to install a larger drum. In turn, pistols chamb...ered for blank cartridges usually more or less correspond in terms of magazine capacity to the firearm models from which they are copied; here you can find models that can hold from 5 to 30 charges.

The number of shots on one gas station that an air pistol or revolver is capable of producing. Specified for gas models and PCP (see "Type"); in the first case, the data is usually given for a standard 12-gram cartridge with carbon dioxide, in the second case, for a full filling of the built-in reservoir.

Note that this parameter is quite approximate, since the actual number of shots at a gas station may differ slightly from the claimed one. Nevertheless, according to the claimed number of shots at a gas station, it is quite possible to evaluate different models of pneumatics and compare them with each other. However it must also be taken into account that the last portions of gas / air pressure is noticeably reduced — and this reduces the initial velocity of the bullet and the firing range, and can also lead to problems in the operation of blow-back systems (see below). So if the number of shots from one gas station is important for you, you should proceed from the fact that the number of “effective” shots (with full bullet speed) will be somewhere 10-15% less than the maximum claimed.

The type of sighting device provided in the design of the pistol / revolver.

The vast majority of short-barreled pneumatics, "floberts" and starting pistols are equipped with the simplest mechanical sights in the form of a front sight and a rear sight. In pneumatic weapons, models with adjustable and non-adjustable sights are approximately equal; in Flaubert's revolvers, the possibility of adjustment is somewhat less common than non-adjustable front and rear sights ; and in models for a blank cartridge, in principle, it makes no sense to provide adjustment. There are pistols / revolvers without sights at all.

Here are the general features of different types of scope:

— Unregulated. Front sight and rear sight, fixed motionless and without any additional settings. The advantages of this design are simplicity, low cost and reliability; in addition, such a sight is almost impossible to shoot down due to an accidental impact of the front sight or rear sight on a foreign object. The main disadvantage is the actual impossibility of adjustment, which does not allow adjusting the sights for a change in distance, side wind or deviations due to production errors. On the other hand, for recreational shooting at short distances, these moments are not decisive, and serious factory defects are extremely rare in fact. So i...f maximum accuracy is not critical for you, a non-adjustable sight may be enough.

— Adjustable. Sights with the ability to adjust; however, the specific possibilities of such adjustment may be different. One of the most popular options is to adjust the rear sight in height, for zeroing weapons at a specific distance. For this, a micrometer screw is usually used. Another option is a rear sight with the ability to move horizontally, it is mainly designed to compensate for errors in the design of the weapon itself, which give a lateral displacement of the point of impact. The most advanced models — mostly high-precision sports pistols — allow you to adjust the rear sight on both axes. Anyway, an adjustable sight is more complicated and more expensive than an unregulated one, it may require additional adjustment by the user himself, but with such devices you can achieve maximum shooting accuracy.
Also note that on the market you can find pneumatics equipped with optical or collimator sights; they are also adjustable.

— Is absent. The absence of their own sights is an extremely rare option, found in two varieties of pneumatic and similar weapons. The first is some spring-piston and PCP pistols (see "Type") with long barrels and high muzzle velocity, designed for high-precision shooting. They have sight mounts (see below) or slots for such mounts, allowing the shooter to choose the sights to their taste. The second variety is revolvers (mainly chambered for Flaubert) of miniature size, originally not designed for aimed shooting in the classical sense of these words.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

The material from which the body of the gun is made.

The main materials found nowadays are metal and plastic. At the same time, the division into metal and plastic cases is actually relevant only for pneumatics; models for "flobert" and for a blank cartridge (see "Type") are almost all made of metal. As for the features of each of the materials, they are as follows:

— Metal. The key advantages of metal are strength, reliability and similarity to materials used in firearms. Such cases weigh much more than plastic ones, but this moment is also often referred to as an advantage — it further enhances the resemblance to combat pistols / revolvers, creates a sense of solidity and allows you to effectively practice skills in working with weapons. The main disadvantage of metal is its rather high cost. In addition, note that the composition of this material may be different: in particular, in low-cost models, a lighter and cheaper, but less durable silumin or other similar alloy can be used instead of steel.
Separately, it should be said that in some modern firearms (in particular, Glock) only the casing-bolt is made of metal, and the frame and handle are made of plastic. For air pistols and starting pistols made of similar materials, our catalog also lists metal as the body material in order to emphasize the similarity with combat prototypes.

— Plastic. Material used mainly...in low-cost models of pneumatics. In this case, it means a body made entirely of plastic — including a casing-shutter, if available in the design. The main advantage of this material in this case is its low cost — this determined the specifics of its application. On the other hand, plastic is noticeably inferior to metal in terms of strength and reliability, and the small weight of such cases is considered by many to be a disadvantage — the weapon is perceived as a "toy". However there are also advanced varieties of plastic — durable, heat-resistant, suitable even for military weapons; however, in pneumatics, such materials are used in rather expensive copies of real pistols, where a plastic frame is combined with a metal casing-bolt — and such cases are already considered metal (see above).

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).