Comparison Umarex Colt Single Action Army 45 vs Gamo P-25 Blowback Tactical

The form factor determines the layout and operation of the weapon.

In general, air pistols are significantly more common than air revolvers. But in models with a firearm principle of operation, everything depends on the ammunition: the terms "Flaubert's revolver" and "starter pistol" fully correspond to the form factors most common in each of these varieties. The general features of each of the options are as follows:

- Pistol. In this case, pistols include models that do not have an outer drum characteristic of revolvers (see below). At the same time, the specific type of magazine may be different: some models use a box magazine in the handle, like in real pistols, others use internal drums, others are made single-shot, etc. In any case, this form factor is widely the most popular among all varieties , except for models chambered in Flaubert (see "Type"). This is due to the versatility and general convenience of this layout; in addition, most models of handguns are also pistols, so from this point of view, this form factor is also optimal for shooting training. Among the "floberts", pistols are extremely rare, mainly for two reasons. Firstly, this cartridge has an extremely low energy, insufficient for the operation of pistol automation; secondly, the rim on the sleeve is not well suited for box-shaped pistol magazine...s, but it goes well with drums. Because of this, pistols chambered for Flaubert are rare, and the existing models use magazines of a special design: a dummy box magazine, in the upper part of which a small drum is installed.

- Revolver. Initially, a revolver is a weapon in which the role of a magazine is played by a rotating drum, in the cells (chambers) of which charges are located. Before each shot, the drum rotates, and the next cell becomes opposite the breech breech, actually turning into a chamber. (Note that similar magazines are also found among pistols; the key difference is that the turret is installed openly). This form factor is extremely popular in Flaubert chambered weapons due to the fact that the drum magazine is ideally suited for the rimmed case used in such a cartridge. But in classical pneumatics, for a number of reasons, revolvers did not receive distribution. However, pneumatic revolvers are also produced, and they can use an interesting solution that adds realism - false cartridges that mimic the size and weight of real ammunition. A bullet or a ball is inserted into such a false cartridge, as in a sleeve, and the “sleeve” is already placed in the drum chamber.

The model or brand of the combat pistol/revolver from which the product was copied.

Replicas of military weapons are very popular among air pistols. Here you can find, in particular, models that imitate different models of weapons from Beretta, Colt, CZ, Glock, Heckler & Koch, Luger, Smith & Wesson, Sig Sauer, Taurus, Walther, Makarov (PM). Devices chambered for a blank cartridge (see “Type”) are also often copied from “firearms,” but in Flaubert’s revolvers the situation is different - most of them have a certain “average revolver” shape and design that is not related to a specific model of military weapon.

On the one hand, copies are popular among gun fans who, due to legal restrictions, cannot acquire a full-fledged short-barreled firearm. On the other hand, a pneumatic or launch copy often reproduces all the controls of the original. As a result, it often happens that a replica of a real-life model turns out to be even more convenient to use than the original.

The working length of the barrel installed in the pistol / revolver is from the chamber to the muzzle. In airsoft models (primarily AEGs, see "Type"), the length of the inner barrel is indicated, along which the bullet directly moves. Three main points directly depend on this parameter: the initial velocity of the bullet, the length of the aiming line and the dimensions of the weapon.

In short-barreled (up to 20 – 25 cm) pneumatics and Flaubert's revolvers, a long barrel allows you to achieve higher initial speeds. However there is no rigid dependence here, and models with the same barrel sizes can differ markedly in initial speed (especially since the latter also depends on a number of parameters, primarily the principle of operation — see "Type"). However, long-barreled pistols are generally better for long-range shooting than short-barreled pistols. This is due to the second nuance — the length of the sighting line: a long barrel allows you to increase the distance between the front sight and the whole, thereby reducing errors in aiming. However, with regard to dimensions, the increase in the length of the barrel not only makes the weapon more cumbersome, but also worsens its balance, since the centre of gravity shifts forward because of this.

There are a couple more nuances associated with this indicator. So, in copies of combat pistols (see above), the barrel length is selected in accordance with the size of the weapon from which this model wa...s copied. And for products chambered for a blank cartridge (see "Type"), this parameter is not indicated at all, since there is virtually no full-fledged barrel in such pistols.

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The type of barrel fitted to the pistol.

Smooth-bore pneumatics in our time is much more common than rifled ; Flaubert revolvers with smooth and rifled barrels on the market are approximately equal; and models for a blank cartridge are equipped exclusively with muffled barrels. Here are the features of each option.

— Smooth. Trunks having a smooth, rifling-free inner surface. The main advantage of this option can be called ease of production and, as a result, low cost. In addition, in the case of pneumatics, the smooth barrel is "omnivorous", with it you can use both bullets and balls (although most often such pistols are compatible with only one type of ammunition). We also note that the airsoft "weapon" in principle is made only with a smoothbore; and the absence of rifling greatly simplifies cleaning, which is especially important for models chambered in Flaubert. On the other hand, in smooth barrels, the bullet is not stabilized by rotation, and the dispersion of such weapons is noticeably greater than that of rifled ones. This does not play a special role in recreational shooting at short distances, however, this type of barrel is not suitable for high-precision weapons.

- Rifled. Barrels with spiral grooves on the inner surface. Due to the rifling, the bullet spins around the longitudinal axis while m...oving along the barrel - this provides additional stabilization and reduces the weapon's own dispersion. Actually, higher accuracy is the main advantage of rifled models over smoothbore ones; and "serious" sports pistols for high-precision shooting are equipped only with this type of barrel. The disadvantages of this option include, first of all, the higher cost than that of smooth ones, as well as the additional difficulty in cleaning - it can be difficult to thoroughly clean the rifling. In addition, in the case of pneumatics, rifled weapons are designed mainly for bullets and are poorly suited for cheaper balls: in most cases their use is not allowed at all, and where allowed, it is desirable to use special soft lead balls. This is due to the fact that the hard metal from which most balls are made wears the rifling a lot; and the promotion of such a charge turns out to be uneven and does not stabilize it, but, on the contrary, leads it away.

- Silenced. A variant found exclusively in pistols chambered in blanks. In such devices, a special plug is installed that blocks the bore and completely eliminates the possibility of firing any projectile (be it a bullet or shot). We emphasize that an attempt to fire from such a “weapon” with a non-blank cartridge (even with a rubber bullet) will most likely lead to a rupture of the barrel and serious injuries to the shooter and people around him.

The type of ammunition that the pistol/revolver is designed for.

Pneumatics can use balls or lead bullets, and some models are compatible with both varieties at once. In weapons chambered for Flaubert and a blank cartridge, the type of ammunition is already obvious from the name. Here is a more detailed description of each option:

— Balloons. Ordinary round balls; for traditional 4.5 mm pneumatics they are made of metal, for airsoft guns of 6 mm caliber they are made of plastic (although other materials are occasionally found). Actually, the airsoft "weapon" by definition uses only balls, it is not made for other types of charges. As for classical pneumatics, here the main advantage of this option can be called a low cost — balls are somewhere much cheaper than lead bullets. In addition, they have good penetrating power, and magazines and reloading systems for balls are extremely simple. On the other hand, such ammunition is less suitable for accurate long-range shooting. Firstly, balls are inferior to bullets in terms of ballistic characteristics; secondly, they are usually made of hard steel and are practically unsuitable for working with rifled barrels. On the other hand, for recreational shooting and simple training at a relatively short range, these points are not critical; so it is this type of ammunition that is most common in modern air pistols.

— Lead bullets. A bu...llet in this case is called a projectile of a directional shape, with a clearly defined front and rear. The specific form of such projectiles may be different, but they all have a number of common features. So, any bullet at the same initial speed flies further and hits more accurately than a ball. And the material is usually lead or another soft metal, which provides a number of advantages. Firstly, bullets work great with rifled barrels: the edges of the bullet clearly fit into the grooves on the inner surface (many bullets are even able to expand slightly at the time of the shot, for the tightest possible fit in the barrel), the projectile is effectively untwisted and stabilized, while the rifling is worn minimal. Secondly, bullets flatten out when they hit a more or less hard surface — this minimizes the risk of ricochets. At the same time, bullets are more expensive than balls, and in multi-shot models, they require a more complex design of magazines and reloading mechanisms. As a result, this type of ammunition is relatively rare in short-barreled pneumatics — mainly in professional long-range pistols, as well as in models where this is due to design features (in particular, bullets are better suited for spring-piston “breaks”).

— Balls / lead bullets. The ability to use both types of ammunition described above at once, to choose from. Note that such versatility can be implemented in different ways: some pistols / revolvers are indeed universal in terms of the type of ammunition (unless each variety needs its own magazine), others are produced in two separate versions — for bullets and for balls. This point should be clarified separately before buying. It is also worth considering that in "omnivorous" weapons with a rifled barrel, it is better to use bullets if possible, and balls should be considered as a fallback. This is due to the fact that the balls are poorly compatible with such weapons; see "Barrel" for details.

— Flaubert's cartridge. Small-caliber (4 mm) cartridge, which is actually a primer with a bullet, without a powder sample (or with a very small amount of gunpowder — in the form of a few grains). In fact, it is a firearm, however, in terms of ballistic characteristics, a weapon chambered in Flaubert is comparable to pneumatics, due to which in many countries it is officially equated to pneumatic and sold without special permits (however, this point needs to be specified separately). Note that the vast majority of weapons chambered for this cartridge are revolvers; pistols are rare and have a specific design (for more details, see "Form Factor").

— Blank cartridge. A cartridge with a case, a primer and a powder charge, similar in design to a full-fledged firearm, except that it does not contain a bullet. Instead, the case mouth is crimped in the form of an "asterisk" or covered with a plug made of an easily destructible material like plastic. Note that such cartridges can be used not only in specialized “weapons” (see “Type”), but also in most traumatic and combat pistols of the corresponding caliber; however, blank pistols usually do not require special permits, and anyone can practice basic skills with them (including working with recoil and reaction to a shot).

The capacity of the magazine provided with the pistol, or the drum installed in the revolver (see "Form factor"). For obvious reasons, it is indicated only for multiply charged models (see "Charging capacity").

Repeatingly charged air pistols / revolvers are conditionally divided into models with magazines up to 15 charges and more than 15 charges. The largest capacity here is airsoft AEGs (see "Type"), copying submachine guns — they are not uncommon in stores for 50 balls or more, and as additional accessories for many models, so-called "bunkers" are produced, where the number there are already hundreds of charges. As for traditional pneumatics, it is worth noting that if the pistol is designed for bullets and balls at the same time (see "Type of ammunition"), then the capacity when using different types of charge may vary — usually, it is higher for balls in such cases, and this figure and indicated in the characteristics as the main one.

As for the weapon chambered for Flaubert, in it the “classic of the genre” is a revolver with a drum for 9, less often for 8 rounds. A greater number of charges is not found — for this the drum would have to be made too bulky; a smaller number — about 5 – 6 rounds — can be found in individual revolvers, as well as models in the form factor of a pistol, where the dimensions of the case do not allow you to install a larger drum. In turn, pistols chamb...ered for blank cartridges usually more or less correspond in terms of magazine capacity to the firearm models from which they are copied; here you can find models that can hold from 5 to 30 charges.

The presence in the pistol of the Blow-back system — a mechanism that simulates the operation of automation and the recoil of a real weapon. Note that blow-back models are found only among air pistols; in weapons chambered for Flaubert (see “Type”), such systems are not applicable due to the extremely low energy of the ammunition, and for pistols chambered for a blank cartridge, the term “Blow-back” itself is not relevant — they already use full-fledged automation, the same as in firearms.

This feature enhances the resemblance of an air pistol to a real firearm: with each shot, the casing-bolt moves back and forth, creating a characteristic recoil with a barrel toss. The second important nuance is that the blow-back actuation cocks the trigger, reducing the force on the trigger — and this, in turn, makes it easier to control the weapon and contributes to increased accuracy. And in many models with such systems, a full-fledged slide lag is also provided: when the cartridges run out, the casing-bolt is fixed in the rear position, and to continue shooting, you need not only to change the store, but also remove the weapon from the delay. Many amateur shooters appreciate blow-back pistols solely for their general resemblance to combat counterparts, but this feature also has a very practical meaning: it allows you to develop useful skills in working with recoil and reloading weapons. On the other hand, note that gas is additionally cons...umed for the operation of automation; and the muzzle velocity in such pistols is lower than in similar models without blow-back.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.