Comparison Partizan COD-454HM FullHD 5.1 vs Atis AW-H800VFIR-40G

The number of backlight LEDs (see "Design and capabilities") provided in the camera design.

Theoretically, more LEDs provide more power and, accordingly, range (see below) and efficiency of IR illumination or LED illumination. However, in fact, such light sources can vary markedly in performance; in addition, a lot also depends on the features of the camera itself. Therefore, in fact, this indicator is a reference, and when choosing, it makes sense to pay attention to parameters that are closer to practice — in particular, the same backlight range (see below).

Operating range of the backlight (see "Design and capabilities") installed in the surveillance camera. This term usually means the maximum distance from the camera to the observed object, at which it is able to provide a relatively high-quality and legible image in the complete absence of other light sources. Of course, the actual backlight range may differ from the claimed one, and these differences are most often in the direction of increase (for example, due to the presence of the same additional light sources). However, if the possibility of shooting with backlight is important for you, you should focus on the claimed range.

The size of the matrix installed in the surveillance camera (diagonally).

In general, larger sensors (with the same resolution and sensor type) are considered more advanced: they get more light, which has a positive effect on image quality (especially in low light). On the other hand, increasing the size affects the cost of the entire device; and in some cases (for example, if the camera is not planned to be used in twilight and darkness), a relatively small sensor may be quite suitable.

As for specific dimensions, the most modest cameras in terms of this indicator have matrices of 1/4 "or less. Models with sensors of 1/3.8" - 1/3" and 1/2.9" - 1/2" are very popular, these values can be called average. And in advanced devices, diagonals and more than 1/2 "(up to 1/1.7") are found.

Camera sensor resolution in megapixels (millions of pixels).

The higher the resolution of the matrix, the higher the video resolution can be (see below), the more detailed the image is capable of providing the camera. At the same time, note that as the number of megapixels increases (without changing the size of the matrix), the size of each individual pixel decreases, which increases the likelihood of noise and deterioration in the overall image quality. Therefore, high resolution in itself is not necessarily a sign of high quality — a lot depends on other things, for example, on the size of the matrix (see above).

As for specific values, in the most modest matrices it does not exceed 1.3 MP, which corresponds to the maximum HD resolution. 2 MP sensors allow for already Full HD resolution (usually 1920x1080 or 1600x1200), 3 MP, 4 MP, 5 MP and 6 MP are capable of better resolution, but still do not reach 4K, which is typical for 8 MP.

The maximum video resolution that the camera can capture.

The higher the resolution of the video, the more details you can see on it, the less details will be blurry. On the other hand, high resolution means large volumes of video materials, which, accordingly, requires capacious media for their storage and fast communication channels for broadcasting video in real time. Yes, and this indicator significantly affects the cost of the camera.

Resolution of the video signal produced by the camera in TV lines (TVL).

A similar resolution designation is used for analogue video; the number of TV lines in this case is the horizontal size of the image. The meaning of such a recording is that in analogue PAL and NTSC formats, which are most often used in video surveillance systems, the vertical size of the video is always the same (625 and 525, respectively), so the frame size in different models of analogue cameras differs only in horizontal. Accordingly, the higher the TVL number, the more detailed the image will be, the more small details will be visible on it. On the other hand, in order to use all the features of a camera with numerous TV lines, a screen corresponding to these features is also required; For more details on compatibility with the screen, see specialized sources.

As for specific numbers, a value of 500 TVL and less is considered very small, 500 – 600 TVL — modest, 600 – 700 TVL — average, 700 – 800 TVL — above average, and in some models this number may exceed 800 TVL.

The maximum frame rate in the video captured by the camera.

The higher the frame rate, the clearer the image, the less noticeable blurring when moving in the frame (especially fast). On the other hand, this indicator affects the amount of information recorded during shooting, as well as the cost of the camera itself. Therefore, it makes sense to specifically look for a video surveillance camera with high-speed shooting(45 fps and higher) only if a clear recording of fast moving objects is important to you.

The lowest degree of illumination of the scene being shot, in which the camera is able to provide normal visibility. Usually, this item specifies the values for the daytime mode of operation (in the night mode, the minimum illumination in many models may be zero at all, because in such cases the IR illumination is turned on, see "Design and capabilities"). And if the camera is capable of shooting in colour, it usually means the lowest illumination necessary to obtain a colour image.

The lower this indicator, the better the camera works in low light, the brighter and more clearly visible image it is able to provide in such conditions. At the same time, note that in low light, night mode is often preferable, and in the presence of the aforementioned IR illumination, it is more likely to focus on the range of its operation (see above).

There are comparative tables that allow you to evaluate the degree of illumination indicated in the characteristics from a practical point of view: for example, an indicator of 0.2 lux corresponds to clear eyes on a full moon.

Aperture of the lens installed in the camera.

Aperture characterizes the degree of attenuation of the light flux when passing from the front lens of the lens to the matrix. It is denoted as the ratio of the diameter of the active aperture of the lens to the focal length, while the size of the active aperture is designated as f and is taken as a unit — for example, f / 1.4 or f / 2.0. Moreover, the smaller the number in the designation, the higher the aperture (in our example, the second lens will be darker than the first). And for lenses with a variable focal length (see "Focal"), the actual aperture, usually, changes with a change in focal length; for such models, either the range of aperture values, or its maximum value, can be indicated.

By itself, this parameter characterizes, first of all, how light the image taken through the lens turns out, all other things being equal. High values are important, first of all, when shooting in low light conditions: a fast lens allows you to get a fairly high-quality image without increasing the sensitivity of the matrix, which is fraught with noise and “blurring” of the picture. On the other hand, the actual quality of camera operation (including in dark conditions) also depends on many other factors — the type and size of the matrix, signal processing features, etc. Therefore, aperture in most cases is more of a reference than a practically significant parameter.