Comparison NOVA TOUR Han-Tengri 4 vs Tramp Mountain 4

The vestibule is a kind of "entrance hall" in front of the entrance to the main compartment (s) of the tent.

The specific design and purpose of such a "hallway" may be different. So, in small two-layer tents, the space between the inner and outer layers in front of the entrance plays the role of a vestibule (for this, the outer canopy is stretched at a greater angle relative to the vertical than the inner one). The dimensions of such a compartment are small, it is designed mainly for storing individual items, such as shoes. In larger models, the vestibule is made in the form of a full-fledged compartment, which differs from the main compartment only in the absence of a bottom (although there are exceptions). Such a compartment can be located between two sleeping compartments; and in some tents two vestibules are provided at once.

Anyway, such equipment increases the useful area of \u200b\u200bthe tent and provides additional comfort when using it. Tambour can be used to store equipment, often quite bulky; with an open entrance, it provides additional protection for the main volume of the tent from rain, sun and wind; and in a large vestibule(150 cm long or more), you can even organize additional sleeping places (if the weather permits) or even an auxiliary room such as a kitchen, dining room, administrative area, etc. " below.

The length of the vestibule provided in the tent.

See above for more details on the vestibule. As for its dimensions, the length of the vestibule is measured along the same side along which the length of the entire tent is measured; and the width of this compartment usually corresponds to the overall width of the tent, and it does not need to be specified separately in the specifications. At the same time, we note that due to such measurement rules, the length of the vestibule is often less than its width; this is quite normal in this case.

The specific ratio between the dimensions of this compartment in different tents may be different. However, in general, a longer vestibule is usually larger and more capacious than a shorter one. When choosing, it should be taken into account that a large and spacious additional compartment increases overall comfort, but it significantly affects the price and weight of the tent (not to mention its overall dimensions). So when choosing for this parameter, it is worth considering the real conditions and features of the operation of the tent. We only note that in order to organize additional beds, it is worth paying attention to vestibules with a length of at least 150 cm — usually, they can accommodate additional places at least across, and often along the tent.

The number of bedroom entrances provided in tent design.

It is worth clarifying that if there are several bedrooms in the structure (see "Sleeping areas"), then in this case it is not the total number of entrances that is taken into account, but the number of entrances per bedroom. For example, if the tent has 2 sleeping areas, each with 1 input, then the characteristics will indicate 1 input to the bedroom.

In other words, if the design states 2 entrances to the bedroom, this means that each bedroom has two exits (regardless of the total number of bedrooms). Such a design is convenient primarily because you can leave the sleeping slot in the most convenient way, if necessary, without disturbing your sleeping neighbors. On the other hand, a design with one input provides a higher degree of thermal and moisture insulation; such tents are better suited for particularly unfavorable conditions.

— External. The external frame is considered more convenient to set up, especially in the case of double-layer tents (see "Inner tent"), since both the inner tent and the outer awning are put on the frame at once. On the other hand, such a frame is more susceptible to the negative influence of natural conditions and does not allow the inner tent to be set up separately.

— Internal. The internal frame is somewhat more difficult to install than the external one; at the same time, it is less susceptible to the influence of unfavorable external conditions, and in double-layer tents (see "Inner tent") with an internal frame, it is usually possible to install only the inner tent, without an awning.

It should be noted that only tents in the shape of a hemisphere or half-barrel have a classic frame (see "Body shape"); in the case of gable tents, the characteristic "external/internal" refers primarily to the location of the supports, and the term "frame" is not applied at all to tent models.

— Inflatable. In such tents, the role of the frame is played by sealed hollow tubes made of flexible material (rubber or polymers), usually arched. When folded, they can be rolled up quite compactly, and when the tent is set up, they are inflated (usually with a special pump), acquiring the desired shape and sufficient rigidity to support the awning. The advantages of inflatable frames are their...light weight and ease of installation; they usually belong to quick-setup systems (see above for the latter). On the other hand, inflatable elements are very sensitive to damage: a small crack or hole, not critical for an element of a regular frame, disrupts the seal and makes the tent unusable.

— Pop-up. An automatic type of arc frame — it unfolds automatically when the tent is removed from the cover. This type of frame is often used in small budget tents, intended for those who prefer camping, nature trips and music festivals. Such tents are packed in a small round bag, which takes up a minimum of space in a car trunk or among the hand luggage of vacationers.

Both the rigidity of the frame and the reliability and durability of the tent itself depend on the thickness of the arcs. Usually, the larger and more capacious the tent, the thicker the arches are needed for the frame. Arcs made of plastic and fibreglass most often have a thickness of 7 to 13 mm, while steel and aluminium — from 5 to 16 mm. With an increase in the section of the arcs, the weight of the tent in the folded state also increases.

— PU (polyurethane). A polyurethane (PU) coating is applied to the inside of the outer tent. The protective layer of polyurethane increases the moisture resistance of the tent, at the same time, the strength of the awning fabric also increases. The main advantage of polyurethane is the ability to reliably protect seam joints. However, polyurethane protection is not the most effective, besides, the presence increases the weight of the tent. The use of polyurethane protection alone is more typical for entry-level (low-cost) class tents. In good quality tents, PU coating is complemented by other types of protection, often polyurethane is used together with silicone (Si).

— Si (silicone). The outer tent fabric is impregnated with silicone (Si). Silicone significantly increases the moisture resistance of the tent. The fabric impregnated with silicone acquires elasticity, its strength characteristics increase. This type of protection is considered the most technologically advanced and functional. The tent itself is impregnated with silicone (from the outside), and sometimes a PU coating is additionally made from the inside for better water resistance. The main disadvantage is the inability to protect seam joints. For this reason, the seams in silicone impregnated tents are glued separately.

An indicator that reflects the ability of the tent awning to withstand moisture without getting wet. It is expressed in millimetres of water column — the height of the water column that the awning can withstand (the area of impact is out of the question, because the load per unit area under water depends only on the height of the water column and is not related to the area of \u200b\u200bits base). The significant figures indicated in the characteristics (for example, 4000 mm of water column, i.e. 4 metres) are due to the fact that raindrops can have a significant speed and, when they hit the tent, create a load at the point of impact comparable to the pressure on depth of several metres.

In general, the higher the waterproof rating, the better the awning will cope with the effects of rain and snow. Indicators up to 3000 mm w.c. Art. are considered sufficient for places where it rains rarely, awnings for 3000 – 7000 mm of water. Art. allow you not to be afraid of intense downpours, and in expeditionary (see "Destination") tents designed for extreme conditions, this figure can reach 10,000 mm of water. Art. and even more. However, more water-resistant fabrics, usually, have a significant weight, so in each individual case it makes sense to choose the option that is optimal in terms of durability and weight.

— Reflective elements. The outer surface of the tent is equipped with special reflective inserts. Thanks to this, the location of the tent will be visible from afar, which allows users to quickly navigate in the dark, easily determining the location of the tent city / tent. Often, reflective fibers are woven into wind braces so that at night they do not catch on.

— Mosquito net. Fine-mesh mesh covering the openings in the tent: entrances, windows, ventilation openings. Its presence is highly recommended if you plan to use the tent in the warm season: it allows you to ventilate the interior without letting mosquitoes and other unpleasant flying insects inside.

— Lantern loop. A special mount (loop, hook or carabiner), usually under the ceiling, designed to secure the lantern inside the tent. It will allow you to easily organize indoor lighting and eliminate the need to hold a flashlight in your hands or independently find a place for its best location.

— Internal pockets. Pockets located on the inside of the tent. They facilitate the organization of the internal space, allowing you to conveniently place relatively small items — glasses, watches, some tools, etc. It also reduces the risk of accidentally crushing fragile items.

— Shelf for small items. The purpose of t...he hanging shelf is generally similar to the inside pockets (see above): to organize the space inside the tent so that small items are not lost and are not accidentally crushed. In some tents, there may be several such shelves. Shelves are usually located in the upper part of the tent, which allows them to also be used as a stand for a lantern if there are no loops for it (see above) or it is impossible to use it for some reason.