Seasonality
Seasons in which the use of a tent is allowed.
There are three main seasonality options:
winter,
spring / autumn and
summer. At the same time, the design features necessary for comfortable use of the tent in different seasons are as follows:
— In winter, the tent should effectively protect against snow and wind, and its materials and fittings should normally endure a long stay in the cold. Thermal insulation is also desirable, but in general this is a secondary factor — the main insulation is provided primarily by clothing, a sleeping bag and a bed.
— In the off-season — in spring and autumn — protection from rain, which can be accompanied by strong winds, is of particular importance.
— For comfortable use in the summer heat, good ventilation is required, ideally with insect protection, such as mosquito nets.
As you can see, these requirements generally do not contradict each other and may well be combined in one product. Thus, there are very few tents on the market designed strictly for one season — two- or even all-season options are much more common. For example, even among beach tents (see "Purpose") there are models for which the possibility of using in the off-season is claimed — for this, the design provides for a dense awning, or even the ability to completely close the tent. Almost any model from the "spring-autumn" series
...additionally has a summer specialization; and most models suitable for winter actually allow year-round use.
In conclusion, we recall that tents with the same seasonality and purpose can at the same time differ significantly in characteristics and design features.Weight
The total weight of the tent is including the frame and other accessories.
This parameter depends primarily on the purpose (see above), and after that — on seasonality, capacity, and additional functions. For example, in trekking and expedition models, the weight usually does not exceed
5 – 7.5 kg, and the lightest of these products can weigh
2 – 3 kg or even
less, while being full-fledged tents for 2 people or even more. However, for a trekking tent, such a small weight with a capacity of more than 2 people usually means that this model is designed exclusively for the summer. For most camping tents, the weight starts at 6 kg, although among them there are also quite light products — by
4 – 5 kg,
3 – 4 kg, or even less (in such cases, light weight can also mean a purely summer specialization). And the most capacious and/or multifunctional models can have a weight of
10 – 15 kg,
15 – 20 kg and even
more; in this weight category, you can mainly find tents, camping tents for many people and fishing tents for carp fishing (see "Destination").
When choosing a tent according to this indicator, it is worth considering that it does not always make sense to chase the maximum weight reduction. Yes, the
...light tent is the most convenient to carry; on the other hand, weight reduction inevitably affects one or several other characteristics at once. So, most often, lighter models are either more expensive or smaller in size and less roomy and functional than their heavier counterparts. And sometimes weight reduction also negatively affects the security (including moisture resistance) and the overall reliability of the product. Therefore, it makes sense to specifically look for the lightest tent possible in cases where weight reduction is of key importance; a typical example is long trips, in which all the equipment has to be carried “on oneself” for a long time. And even in such cases, it is worth remembering other important characteristics. For example, for use in late autumn, when frosts are likely, it is better to choose a heavier tent with winter seasonality than a light model that is not designed for winter conditions.Inner tent
Models with this feature are actually two tents, one of which is located inside the other. In this case, the outer tent is usually made of a dense waterproof material, and the inner one is made of a light, moisture-permeable material. This design provides good thermal insulation and protection against moisture, including from condensate: most of it settles on the outer tent, without penetrating inside. Many
double-layer tents allow you to set up only the inner tent separately, which can come in handy in warm weather. The disadvantage of this option is the increased, in comparison with single-layer, dimensions and weight.
Quick install system
The special design of the tent frame, which
facilitates its installation.
The specific design of quick install systems may vary. Often, a rigid folding frame is sewn directly into the awning, which eliminates the need to reattach the awning to the arcs every time. An inflatable frame (see "Frame type") or a base made of an elastic material can also be used. The disclosure system itself may also differ from model to model. For example, in many classic tents, an umbrella-type mechanism is used (there are even so-called umbrella tents — see “Purpose”; although the matter is not limited to them). In other models (mostly small products like winter fishing tents), the product is first “flattened” and then bent in a special way, turning into a small flat disk.
The advantage of quick set up systems is evident from the name — they greatly simplify the deployment and folding of the tent. As for the disadvantages, most often this is a high cost due to the complexity of the design, and somewhat reduced reliability (for the same reason). In addition, ease of unfolding does not always mean ease of folding — in some models this is a rather "cunning" procedure.
Number of entrances
This item refers to the total number of entrances to the tent. In most cases, their number also describes the possibility of entering the sleeping area. However, there are models with a large vestibule, in which the input is provided from different sides. Such abundant entry/exit options allow you to use the tent in various situations. For example, focusing on the position of the sun, it will be relevant to open the western or eastern side; landscape conditions will not interfere with the installation of the tent, since one of the exits will remain accessible in any case. Well, for a large company at a campsite, vacationers will not interfere with each other.
Bedroom entrances
The number of bedroom entrances provided in tent design.
It is worth clarifying that if there are several bedrooms in the structure (see "Sleeping areas"), then in this case it is not the total number of entrances that is taken into account, but the number of entrances per bedroom. For example, if the tent has 2 sleeping areas, each with 1 input, then the characteristics will indicate 1 input to the bedroom.
In other words, if the design states
2 entrances to the bedroom, this means that each bedroom has two exits (regardless of the total number of bedrooms). Such a design is convenient primarily because you can leave the sleeping slot in the most convenient way, if necessary, without disturbing your sleeping neighbors. On the other hand, a design
with one input provides a higher degree of thermal and moisture insulation; such tents are better suited for particularly unfavorable conditions.
Main poles
The number of poles provided in the frame of the tent. For hemispherical types (see "Shape") for 2-3 people, not intended for extreme conditions, 2 poles are considered quite sufficient; larger and/or reinforced models may have more poles. In the case of half-barrels, this amount is directly related to the length of the tent.
Arc thickness
Both the rigidity of the frame and the reliability and durability of the tent itself depend on the thickness of the arcs. Usually, the larger and more capacious the tent, the
thicker the arches are needed for the frame. Arcs made of plastic and fibreglass most often have a thickness of 7 to 13 mm, while steel and aluminium — from 5 to 16 mm. With an increase in the section of the arcs, the weight of the tent in the folded state also increases.
Frame material
The material from which the frame of the tent (arc) is made. The main requirements for arcs are strength, resistance to deformation (elasticity) and low weight. Modern tents use several materials with different ratios of these parameters.
—
Aluminium. A fairly common material: it has good strength characteristics and low weight, but it is relatively inexpensive. At the same time, aluminium is prone to deformation under long-term stress (although this is usually not critical even when parking for several days).
—
Fibreglass. Composite material based on a combination of fibreglass and plastic. The main advantage of fibreglass is resistance to deformation: even under prolonged loads, the arcs do not lose their shape. In addition, this material is cheap and light in weight (although somewhat heavier than aluminium). The disadvantage of fibreglass is its sensitivity to low temperatures, which limits its use in winter conditions and at high mountains. However, most people use tents in the warm season, and therefore fibreglass has recently gained considerable popularity.
—
Steel. Steel is the most durable of the described materials, in addition, it holds loads well, almost without deforming. At the same time, steel arcs have a significant weight, and therefore they are rarely used in tents.
— Durapol. A composite material that has appe
...ared relatively recently and is positioned as a more advanced alternative to fibreglass. Durapol has a "puff" design: the outer layer is made of special polymer resins, metal foil is located under it, a synthetic mesh is located under it, and, finally, a layer of fibreglass. According to the creators, arcs made of this material are more durable and resistant to fracture than fibreglass, better tolerate low and high temperatures, as well as ultraviolet radiation, are less susceptible to residual deformations and have less weight.