Comparison Husqvarna 225i vs Husqvarna 340i

The largest tyre size (in chain saws) or disc (in circular saws and some others, see "Device") that is allowed for this tool. Tyres are sized by working length, rims by diameter.

A larger bar/wheel allows for deeper cuts but requires more powerful motors. Therefore, this parameter cannot be exceeded — this can lead to an overload of the engine with all the corresponding troubles. However, in many models with a disc it is physically impossible to install a nozzle with a diameter larger than the maximum allowable.

Also note that saws with similar bar/blade sizes may differ in maximum depth of cut (mostly due to differences in design or power). As for the specific dimensions, they depend on the type of saw (see "Device"). For example, large discs of 450 – 500 mm are found exclusively in stationary chain saws, the maximum figure for cutting models is 400 – 450 mm, for trimming — 300 – 350 mm, and sizes of 500 – 550 mm or more clearly indicate that speech It's about a chainsaw chainsaw bar. Detailed recommendations regarding the choice of a tool for a given size can be found in special sources.

The maximum speed of the chain relative to the material that a saw of the appropriate design can provide (see "Device"). Higher speed allows to achieve faster and cleaner cuts, but requires more engine power; low speed, in turn, reduces productivity, but allows you to achieve good traction with a relatively low engine power. More detailed recommendations regarding this parameter can be found in special sources.

Electronic motor protection in a saw controls the load on the motor and helps protect it from overheating, overload, or damage. If the tool is operating in a mode that is too heavy, the system can limit power, shut off the engine, or prevent it from overheating. This is beneficial not only for user safety but also for extending the lifespan of the saw itself. For example, when cutting dense wood, wet timber, or during long continuous work, such a feature helps avoid costly breakdowns.

The design or set of special elements that reduce the transmission of vibrations from the engine and cutting part to the user's hands. Anti-vibration system makes work noticeably more comfortable, especially if the saw is used not just for a couple of minutes, but longer and regularly.

Thus, the tool tires the hands and forearms less, and the cutting itself often feels more controlled. It is especially useful in chainsaws and powerful reciprocating saws, where vibrations are more pronounced. In practice, this is convenient when sawing firewood, trimming branches, working on beams, or during prolonged demolition, where extra shaking quickly becomes a hindrance.

Battery models that the saw of the corresponding type is compatible with (see “Power source”). This information will be useful in cases where the battery(ies) must be purchased separately, for example, if the tool does not come with a battery at all, if you need to supplement the original package, or if the existing battery has failed.

The noise level produced by the saw during operation. Note that this parameter is rather approximate, because in fact, the “loudness of the work” depends not only on the tool, but also on the material being processed and the characteristics of the environment. Nevertheless, the data given in the characteristics make it possible to assess the comfort of working with the tool. The lower this indicator, the less discomfort the noise will cause, and at high values, even special hearing protection may be needed.

Note that the noise level is usually measured in decibels, and this unit is not linear: for example, a difference of 3 dB corresponds to a difference of 2 times, 10 dB — to 10 times. Therefore, it is easiest to evaluate the noise level using comparative tables. Here is a simplified version of such a table for the range in which modern saws operate:

70 dB — loud conversation of several people in close proximity;
75 dB — a cry in the immediate vicinity;
80 dB — truck engine, mechanical alarm ringing;
85 dB — loud scream;
90 dB — freight car at a distance of 7 – 10 m;
95 dB — subway car at a distance of 7 – 10 m;
100 dB — industrial shop;
110 dB — tractor engine;
120 dB — demolition hammer, thunder from a close lightning strike (pain threshold of auditory perception).

The volume of the oil tank provided in the tool.

In this case, we mean a tank from which oil is supplied to the saw chain (see "Device") to lubricate it during operation. In general, this is a reference parameter that allows you to estimate how much oil is needed for one refueling of the tool.

The total weight of the tool. For petrol models (see "Power Source"), usually, dry weight is indicated, excluding fuel.

In general, it makes sense to pay attention to this parameter primarily when choosing a hand tool. At the same time, note that higher power, a more capacious battery or a capacious tank will inevitably affect weight. However, tools with similar characteristics can and do differ markedly in weight. And here it is worth considering that a lighter model will be more comfortable to work with, but weight reduction may affect reliability and/or cost. In addition, a more massive tool is more stable, it is not so prone to jerks under uneven loads. If we talk about specific numbers, then a weight of 3 kg or less is considered very light, 3–5 kg is relatively small, 5–7 kg is medium, 7–10 kg is significant, and some powerful tools (mainly gasoline) weigh and over 10 kg.

As for stationary saws, weight is of secondary importance for them — it mainly affects the ease of transportation.