Comparison Proove Prism Socket vs Sthor 72372

The length of the cable used to connect the surge protector to the network.

The longer the cable, the farther from the outlet you can install the device. On the other hand, a long cable can be inconvenient over short distances. Models on a coil are deprived of this drawback (see "Type"), this moment is compensated by the actual presence of the coil, but they differ in large dimensions and heavy weight. So when choosing, it is far from always worth chasing the maximum length of the wire.

The highest power consumption of the connected devices that the surge protector can tolerate without consequences (to be more precise, with which it can work indefinitely without overloads, overheating, etc.).

This limitation is due to the fact that the higher the power at the same voltage, the higher the current passing through the equipment (in this case, through the surge protector); and off-design currents can lead to breakdowns and even accidents. And although in order to avoid these consequences, modern filters often provide various types of protection (see above), however, the operation of protection is still an emergency situation that is best avoided. Therefore, it is worth choosing a model according to this parameter in such a way that the maximum filter power is at least not lower than the total power consumption of the load. And it is best to have a margin of 20 – 30% — this will give additional guarantees in case of various deviations in the operation of the connected equipment.

Separately, it is worth highlighting the situations when the filter is planned to be used for the so-called reactive load — electrical appliances that widely use circuits on capacitors and/or inductors, for example, power tools or refrigeration units. The total power consumption of such devices (written in volt-amperes) can be much higher than the active power (which is indicated in watts). The recommended line filter power in such cases is calculated using special...formulas that can be found in the relevant sources.

The maximum energy absorption provided by the mains filter, namely, the maximum pulse energy at which the device can safely absorb and dissipate it, completely protecting the connected load. The higher this indicator, the more reliable the filter, the more powerful power surges it can handle. In inexpensive models, the maximum absorption is calculated in tens of joules, in the most advanced models it can exceed 1000 J and even 2000 J.

The cross-sectional area of the wire used to connect the filter to the network. The larger the cross-sectional area, the thicker the wire, the more reliable it is and the more current it can pass without overheating. Accordingly, thick wires ( 1.5 mm² and 2.5 mm²) are a must for high power devices. At the same time, modern manufacturers, usually, choose the cross-sectional area in such a way as to guarantee the safe operation of the filter at the claimed maximum power (see above). Therefore, in fact, a model with a thicker cable than other similar devices should be chosen if it is supposed to be used in unstable networks in which power surges often occur. If the cross-sectional area seems too small for you ( 0.75 mm² or 1 mm²) for the claimed power, there are special formulas that allow you to check the validity of such doubts.

The presence in the design of the surge protector of a special indicator (usually in the form of a light bulb) that indicates that the device is turned on.

This function provides the presence of at least one common indicator; and on models with switches per outlet (see below), additional indicators can be installed on the outlets. Anyway, such equipment makes working with the surge protector more visual, allowing you to immediately assess the status of the device and avoid some unpleasant situations (for example, imaginary equipment breakdowns — when a “faulty” device does not work just because the filter is not turned on).

The indicator can be installed directly in the switch (general or for each outlet, see the relevant paragraphs for details).

The number of sockets with type F grounding, provided in the design of the mains filter.

In this case, we are talking about full-size European type F sockets with metal ground clamps on both sides at the edges of the socket. The "socket" in this case means a CEE 7/4 ("Schuko") standard plug. Grounding is required for the safe operation of some types of electrical appliances, in particular, washing machines and other machines that work with water, refrigerators, computers, audio equipment, etc. A detailed list can be found in the reference literature. If you plan to connect such devices through the filter, this filter must have sockets with grounding.

The number of sockets with type E grounding, provided in the design of the mains filter.

French Type E sockets use a two-hole pattern for the supply of electrical current and an integrated earth pin just above the center plane of the socket. Plugs for them are made with a characteristic hole for a grounding contact.

Number of USB-A ports for charging included in the power strip design.

These ports don't serve any other function than powering and charging external devices, such as smartphones or tablets. Having such connectors in a power strip can be especially convenient when a "230-to-USB" adapter is not available, and there are few USB ports on a computer or laptop, making their use for charging a "luxury you can't afford."

Number of USB-C ports in the power strip design.

These ports serve no other function than powering and charging external devices, such as smartphones or tablets. Having such connectors in a power strip can be especially convenient when a "230-to-USB" adapter is not available, and there are few USB ports on a computer or laptop, making it a "luxury" to use them for charging.