Comparison DeWALT DCG418N vs DeWALT DCG412N

The speed of rotation of the working attachment, which is capable of providing a grinder of the appropriate design (for example, angle — see "Type"). If the device has speed control, this paragraph shows the range of such adjustment, from minimum to maximum.

It makes sense to compare by this parameter units belonging to the same type and having the same maximum diameter of the disk (or other working nozzle). The latter is due to the fact that the larger the disk, the faster its edge moves (at the same speed); i.e. a larger diameter requires less RPM for the same performance/efficiency. In general, when comparing different models, the following should be taken into account. The higher rotation speed is well suited for large volumes of work (because it improves productivity) as well as for fine polishing with “delicate” nozzles. A lower setting, in turn, improves accuracy (reduces the chance of removing excess material), as well as provides more torque and allows you to more effectively deal with hard, stubborn materials. More detailed recommendations for different types of work and different nozzle diameters can be found in special sources; here we note that an increase in the rotation speed, usually, affects the cost of the machine compared to analogues (since this requires a more powerful engine). In addition, discs and other attachments may have maximum RPM limits.

A safety system that turns off the tool when there is a critical increase in load. The specific operation method of the electronic motor protection can vary. For example, in some models, it shuts off the motor when there is a sharp increase in load on the working attachment, such as when the disk jams in the material; this helps avoid sharp jerks of the tool, breakage, disk destruction, and other unpleasant consequences. In other models, the protection responds to overheating or a critical excess of current strength. There are also tools that combine both options.

A special brake that stops the engine shaft from rotating after the power is turned off. Thanks to this device, there's no need to wait for the grinder attachment to stop spinning by inertia after finishing work — the rotation stops in just a couple of seconds (whereas without a brake, it could take several tens of seconds). The engine brake not only enhances work safety but also positively affects the tool's lifespan.

Kickback protection is a set of solutions that reduces tool jerking and twisting when the disc binds in material (concrete, metal, stone). It is implemented in two ways: mechanical safety clutch and electronic systems. The clutch (for example, S-automatic from Metabo, SJS/SJS II from Makita) disengages the drive when the torque increases sharply, saving the gearbox and wrist—the tool does not "shoot" out of hands and does not tear gear teeth. Electronics (Bosch KickBack Control, DeWalt E-CLUTCH, Hilti ATC, HiKOKI/Hitachi RFC, Milwaukee AUTOSTOP, Makita AFT) monitors current and accelerations, instantly shutting off the motor and often, in conjunction with a brake, quickly stopping the disc. In comparison: the clutch works even without power, providing a smooth "slip," but the disc continues to rotate briefly; electronic protection shuts down the motor "to zero," but requires functioning electronics and sometimes a restart. In practice, this is important during grooving and cutting of reinforcement, when the risk of binding increases: with protection, the operator controls the tool, reduces dangerous jerks, and protects the gearbox—whether it is a compact 125-mm cordless grinder or a powerful 230-mm corded model.

— Speed Controller. The ability to limit the engine's maximum speed. Essentially, this function is a smooth speed adjustment; it's convenient when full speed isn't required — for example, in delicate tasks where precision is more important than performance. Note that this feature is found in all types of sanders — including those with a vibrational or belt operation (see "Type"): even in these machines, the vibration frequency or belt speed is determined by the engine's rotations.

— Speed Maintenance. The ability to maintain a set number of rotations regardless of the load on the working attachment. This function is implemented through automation, which adjusts the engine's power accordingly — increasing it under more load and decreasing it under lighter load. Constant rotation speed positively affects both the quality of processing and the lifespan of the working attachments and the tool itself.

— Brushless Motor. The presence of a brushless motor in an electric sander (see "Power Source"). These motors are considered more advanced than traditional brushed motors: they are more energy-efficient, quieter, and do not spark, which can be crucial in fire-hazardous environments. The main downside of brushless motors is their high cost.

— Lighting. This feature is undoubtedly desirable when working in lo...w-light conditions. However, it can also be useful in bright external light: the work area often ends up in shadow (e.g., from the tool itself), making it difficult to work without special lighting.

— Display. A built-in display that can show various information about the device's operation and status. Such a screen provides additional convenience and clarity, but overall, it is quite a specific feature that is rarely found in modern power tools.

— Smartphone Synchronization. The ability to connect the tool to a smartphone or other gadget (like a tablet) via Wi-Fi or Bluetooth. Such a connection is usually used for adjusting work parameters; it's often more convenient to do this through a mobile app than through the controls on the tool itself.

— Rotating Main Handle. The ability to rotate the main handle of the sander around the longitudinal axis. This feature is mainly found in angle models (see "Type") — it provides extra convenience, allowing you to adjust the handle's position according to the situation. This is important for working in unusual positions and hard-to-reach areas.

— Keyless Disc Replacement. The ability to change discs in a sander (usually angle, see "Type") without using keys and other additional tools. The convenience of this feature is clear: you don't need to constantly have a key on hand, keep track of it not getting lost, etc. However, keyless mounting is considered somewhat less reliable than keyed mounting, so it's rarely found in heavy-duty professional models.

— X-LOCK Mounting System. An advanced mounting system for the working attachment, used in some angle machines (see "Type") — predominantly made by Bosch and Makita. This system is somewhat more expensive than traditional 22-millimeter mounting using a nut or washer, but it has several advantages. Firstly, X-LOCK provides the simplest and quickest installation: no need to fuss with additional parts or tools, just place the disc on the spindle and press until it clicks; for removing the attachment, just press a button that disables the lock. Secondly, you can only install the attachment in one correct way relative to the tool — the design of the mounting disallows any other way. The main disadvantage of machines with this system is their incompatibility with cheaper and more common 22 mm standard discs; fittings under X-LOCK are not yet available in every hardware store.

— Collet Chuck. A specially designed chuck used in straight grinders (see "Type"). The grip of such a chuck consists of several elastic petals (usually 2-3) that compress when tightened, securing the working attachment. The main advantages of collets are the speed and convenience in changing attachments, simplicity of design, and low cost.

— Coolant Supply (Coolant). The ability to supply coolant to the work area. This function is mainly found in machines for stone and concrete (see "Type"), as water cooling is most relevant for these materials: it not only prevents overheating but also reduces dust formation. The machine provides a nozzle directed at the working attachment and a fitting for connecting to a water hose.

— Dust Collector Connection. The ability to connect a dust collection container to the tool for collecting dust and other debris generated during operation. Such a container may come with the machine, but this is not guaranteed, and this point should be clarified separately. In any case, a dust collector, while not providing 100% protection against debris, significantly reduces it and simplifies cleanup afterward. Dust collectors can be either reusable or disposable.

The name of the battery platform supported by the instrument.

The battery platform is a battery standard used to keep different power tools and other equipment of the same brand (pressure cleaners, flashlights, etc.) could use the same power supplies and chargers for them. This eliminates the need to use a different battery and “charger” for each individual device, and also makes it easier to find compatible power sources: instead of checking a list of compatible batteries, you just need to make sure that the battery you select is from a supported platform. (However, models of compatible batteries can also be specified in the specifications — see below for more details).

Batteries of the same platform mainly differ from each other in terms of capacity — and, accordingly, cost.

The operating voltage of the battery in the grinder with the appropriate power supply (see "Power supply"). The more powerful the tool, the higher the battery voltage, usually. At the same time, this parameter is usually selected in such a way as to optimally match the characteristics of a particular model; therefore, in fact, voltage data may be required only when looking for a spare or additional battery.

Battery models that the device of the corresponding type is compatible with (see "Power source"). This information will be useful in cases where the battery(ies) must be purchased separately, for example, if the tool does not come with a battery at all, if you need to supplement the original package, or if the existing battery has failed.

Approximate noise level generated by the grinder during operation. Note that this indicator is quite approximate, because. actual "loudness" can vary markedly depending on the type and shape of the material being processed, the surface it is placed on, and other circumstances. In addition, different manufacturers may use different measurement methods. Nevertheless, this indicator makes it possible to assess how comfortable this or that model is in operation and whether special hearing protection is required.

The most “quiet” modern grinders give out about 65 dB — this is comparable to loud speech at a distance of 1 m; in the loudest, the noise level reaches 107 dB — this is the volume of an industrial workshop.