Comparison Anex Cross 2 in 1 vs mima Xari 2 in 1

The ability to adjust the tilt between the seat and the backrest of the stroller. This helps to find the most comfortable position for the baby and adjust the seat to different situations: for example, at the end of a long walk, the backrest can be tilted back for a tired baby to take a nap.

The ability to adjust the tilt of the main unit relative to the stroller frame. This allows you to adjust the stroller to different situations: for example, at the beginning of the walk, the unit can be installed almost vertically, based on a sitting position, and later tilted back so that the baby can take a nap.

The ability to adjust the height of the main unit (where the kid is placed) on the pushchair frame. Different location options have their own characteristics: for example, with a high installation, the kid will be closer to the parent, and with a low installation, stability increases and the pushchair will behave better on uneven roads.

The ability to adjust the position of the footrest, on which the legs of the baby in the pushchair rest.

A similar ability is found in some pushchairs, transformers and pushchairs of universal pushchairs (see "Design"). The footrest itself is an inclined surface attached to the front edge of the seat. Adjustable footrests are those in which the angle of inclination can be adjusted; in many models, this footrest can even be set horizontally. This makes it possible to choose the most comfortable position for the baby's legs in different situations.

The presence of a separate crotch strap in the design of the stroller. Only pushchairs with a bumper (see above) are equipped with such a strap: it is located vertically between the legs of a seated kid, preventing him/her from falling out by slipping under the bumper. In general, this design is similar in purpose to three-point harnesses (see “Harness type”), however, in a stroller with a bumper and crotch strap, the child is usually less crowded. You should pay attention to the presence of this function when buying pushchairs.

A window made of transparent or translucent material, built into the hood that covers the cradle or seating unit. In the version with a walking block, the viewing window is usually located so that the parent can see the baby directly while moving, without being distracted from controlling the stroller. In cradles, the parent can see the child through a window by approaching the stroller from the side of the hood (that is, on the opposite side of the handle); implementations with a window in the front hemisphere of the hood are less common. In addition, a baby lying in a cradle can usually see the outside world through the window (primarily the sky above the stroller). The viewing window can be made in the form of oilcloth or a mesh mosquito net, through the holes of which air freely penetrates, but insects and small debris raised by the wind are retained.

The depreciation theme is designed to absorb shocks and bumps from uneven road surfaces. The most popular nowadays are models with spring systems; you can also meet the shock absorption of the articulated and double types, and in quite a large number of pushchairs this function is absent at all. Here are the main features of each option:

— Spring type. Depreciation systems based on classical springs mounted on individual wheels. They are used in all types of pushchairs except classic pushchairs (see "Design"). The simplest models use a single set of springs, while more advanced models may include additional comfort features such as SAS shock/vibration absorption technology. Whatever the case, depreciation systems of this type are simple yet practical, efficient and reliable.

— Articulated type. The type of depreciation used in pushchairs with carrycots - classic, universal, transformers. The frame, on which the carrycot or seat unit is installed, in such models is attached to the base of the pushchair with the help of special bridges, which play the role of depreciation. As bridges can be used belt hinges, such systems can also refer to the articulated. Anyway, this type of depreciation is excellent for carrycots. First of all, the pushchair is as smooth and soft as possible, which contributes to the comfort and deep sleep of the child (and the parent to...drive the pushchair is much easier, especially on uneven surfaces). Secondly, the carrycot on such a pushchair can be rocked back and forth, lulling the baby. On the other hand, such systems are poorly suited for pushchair frames with swivel front wheels; and the failure of one absorber leads to tilting of the carrycot.

— Double. This term most often refers to the spring systems described above with additional shock absorbers on the frame of the pushchair. Such systems help to maximize vibration reduction and can approach articulated systems in terms of efficiency (see above). On the other hand, the softness of the suspension can be inconvenient when overcoming curbs and other bumps: to raise the front wheels of the pushchair, you have to press hard on the handle.

— Is absent. Pushchairs without depreciation are not suitable for uneven surfaces: in such conditions, the pushchair will be shaken violently, which creates both discomfort for the baby and inconvenience for the parent. On the other hand, such models have advantages over pushchairs with depreciation. First, due to the lack of unnecessary parts, they are much cheaper, and the design itself is as simple as possible and at the same time reliable. Secondly, without depreciation, it is easier to overcome curbs and other obstacles: to raise the front wheels, it is enough to push a small pressure on the handle. Thirdly, such pushchairs rock less on smooth, wave-like uneven surfaces.

The main material from which the frame of the pushchair is made.

— Aluminium. The material used in the vast majority of modern pushchairs of all price categories. This is due to a number of advantages: aluminium is light and at the same time durable, it does not rust and is not afraid of moisture, it lasts a long time, it looks nice, but it is relatively inexpensive — somewhat more expensive than steel, but noticeably cheaper than more advanced materials like carbon.

— Steel. Steel frames are as strong as aluminium frames, and they are much cheaper. On the other hand, they are quite heavy, so steel is used less often in pushchairs.

— Magnesium alloy. Premium Material: Stronger and more durable than aluminium, just as lightweight, but at a significantly higher cost. It is extremely rare, in single models of expensive pushchairs.

— Carbon. Another high-end material: carbon fiber filled with plastic. This combination gives excellent strength - comparable to steel — at a very low weight. However, carbon is very expensive, and these advantages are rarely decisive for pushchairs — in most cases simpler materials are enough. That is why carbon frames have not become widespread.

— Plastic. Plastic itself is easy to manufacture and relatively cheap; it is also not as cold to the hands in cool weather as aluminium or steel. However, modern pushchairs very rarely have frames made of this material. The fact is that low-cost vari...eties of plastic are not strong enough for this; and high-quality varieties cost accordingly - their price is close to aluminium, or even higher.

— Fibreglass. In this context, "fibreglass" typically refers to glass fibers mixed with plastic filler. Unlike conventional window glass, glass fibers are flexible and strong. The plastic filler enhances durability by offering scratch and tear resistance. The result is a material that is lightweight and very strong. However, fibreglass is prone to brittleness, especially with point impacts, and is susceptible to abrasion. As a result, it isn't widely used in pushchairs.

The diameter of the front wheels installed in the stroller.

At the same time, the front wheels are not as important for mobility as the rear wheels: for example, to overcome obstacles, the stroller is often lifted "on its toes" by tilting it towards itself, with only the rear wheels working. Therefore, the diameter of the front wheels may be noticeably smaller than the rear wheels. It should be noted here that the small size also has its advantages — the wheels are lighter.

Speaking of specific numbers, diameter up to 15 cm is considered very modest, 16 — 20 cm — small, 21 — 25 cm — medium, 26 — 30 cm is larger than average and more than 30 cm is large.