Comparison Kugoo M365 Pro Max vs Kugoo Kirin S1 Pro

The power of the motor installed in the electric scooter. In models with two motors (one per wheel), their total power is usually indicated.

A more powerful motor, on the one hand, has a positive effect on the speed and acceleration characteristics; on the other hand, it affects the cost of the device and requires more capacious batteries, which affect both the price and weight. In addition, at acceleration and low speeds, the scooter can be “helped” by pushing off with your foot. Therefore, in most modern models, the motor power is low — most often in range of 250 W, 300 W, 350 W. Power of 500 W is considered quite high, it allows you to reach speeds of 40 km/h and even higher. In the most advanced models, power is already measured in kilowatts, and the maximum speed can exceed 80 km/h; however, such "monsters" cost accordingly.

However, power also affects the ability to drive a vehicle, because depending on the country, various traffic rules are provided for driving a scooter.

The maximum climbing angle that an electric scooter can overcome on engine power alone, without the help of legs. Models with engines of the same power may differ in this indicator (due to the difference in torque and wheel size).

Note that in the specifications the angle is usually indicated in degrees, while on road signs it is given as a percentage (1% corresponds to a rise of 1 m for every 100 m of horizontal movement). However, this moment is not particularly critical: if you often have to overcome a certain hill, you can clarify its slope by converting percentages into degrees (and vice versa) according to special tables. In addition, if the angle turns out to be too large, nothing prevents you from helping the scooter with your foot, in extreme cases, to overcome the climb on foot.

The type of drive in the design of the scooter determines to which wheels the traction from the electric motor is transmitted.

- Front. The drive to the front wheel pulls the entire electric scooter. It provides improved stability on the road, minimizes the likelihood of skidding in corners, and guarantees a soft start and smooth acceleration. On the other hand, the electric motor at the front increases the weight of the wheel assembly and increases the effort when turning the handlebar.

- Rear. Rear-wheel drive electric scooters are not as stable on the road as front-wheel drive models. However, they are more frisky, demonstrate dynamic acceleration and easily conquer hills.

- All-wheel. Scooters with all-wheel drive combine all the positive qualities of front- and rear-wheel drive models in one package. They are also best suited for off-road driving — the all-wheel drive chassis does not care about pits and steep hills, other road irregularities, or mud deposits on the road.

The type and size of wheels used in an electric scooter.

The size is selected by the manufacturer depending on the general purpose of the scooter - whether it is an asphalt road or rough terrain. If we compare similar models with different wheel diameters, then it is worth considering that the larger the wheels ( 10" and larger), the better they handle road unevenness, the higher the cross-country ability and softness of the ride. And small wheels (for example, 8") in turn, they are excellent for smooth asphalt and dynamic driving; they accelerate easily and allow you to make sharp turns.

As for the different types of wheels, there are polyurethane, rubber, inflatable. More details about each:

- Polyurethane. Wheels with solid polyurethane tires. This material provides good shock absorption, high-quality road grip and at the same time good rolling ability; it is resistant to temperature changes and damage, durable, and inexpensive.

— Solid rubber. In this case, we mean wheels with solid rubber tires (inflatable wheels are taken to a separate selection point). In terms of its main characteristics, rubber is similar to the polyurethane described above, and in some respects even surpasses it. Thus, such tires do not make nois...e, smooth out asphalt roughness well, have excellent grip and provide high braking efficiency. On the other hand, this material is less durable and does not tolerate temperature changes well.

— Rubber inflatable. The most advanced type of wheels found in modern scooters. This type of wheel has an inflatable tire (like a bicycle), which provides excellent shock absorption, tight traction and high maneuverability. The disadvantages of inflatable tires, in addition to the price, include sensitivity to punctures and increased difficulty in maintenance: you need to monitor the pressure and, if necessary, inflate the tire.

— Rubber gel. Tubeless wheels filled with gel are insensitive to minor punctures and cuts. Coming out, the gel in the tire hardens almost instantly upon contact with air, effectively sealing the damaged area. In addition, such wheels require virtually no maintenance - they do not need to be inflated. The disadvantages of gel tires include their high cost and somewhat greater rigidity than inflatable tires (although such wheels are still noticeably superior to rubber wheels in terms of softness).

Among the various types of brakes in scooters, you can find rim, disc, drum, electric. There are also models without a front brake.

- Rim. The rim brake is considered the simplest type of braking system. Such brakes provide a smooth deceleration and a complete stop of the scooter at an average speed. The stopping distance is usually medium or long. The rim brake is represented by pads, which, using a special mechanism, are pressed against the wheel rim. The pads themselves are driven by a lever, which is placed on the handlebar. Among the advantages of a rim brake are low price, and simple design. And drawbacks are fairly quick wear of the pads and the need to adjust the brakes as the friction linings wear out. Additionally, when using a scooter with a rim brake, be aware that the pads become less grippy if the rim is wet. In rainy, cloudy and slushy weather, the rim brake cannot be relied upon.

— Disk. Disc brakes are considered more advanced than rim brakes. The disc brake allows the scooter to stop quickly enough, and the braking distance itself can be either minimal or medium. Such brakes are represented by a friction clutch that acts on a small-diameter disc. The disc is attached to the wheel axle. The clutch is pressed against the brake disc with a sufficiently large force, which allows the disc brakes to b...e effective even when wet on the clutch. The disc brake is controlled by a lever that is placed on the handlebar. The advantages of a disc brake for a scooter are reliability, durability and the ability to stop quickly. Among the shortcomings, we highlight the high price and the need to adjust as the friction clutch wears out.

- Drum. Drum brakes slow down well and provide a fairly quick stop. In terms of efficiency, the drum brake for a scooter is between the rim and disc brake systems. The drum brake uses pads that are located inside the rim. In this case, the friction plates act on the inside of the rim. The brake with a drum device has many advantages: a large friction contact surface, moisture protection, reliability and durability. Among the shortcomings can be noted: the use of massive wheels, the complexity of service maintenance, and the need for periodic adjustment.

- Electric — braking with the help of recuperation. In this case, the deceleration and stop are produced by the electric motor itself, by reducing the speed. Usually, the electric brake provides a soft and smooth stop. As a rule, the electric brake acts as an auxiliary brake system. Also, advanced scooters often use a recuperative electric brake. In this case, when the speed is slowed down, energy is recovered, which allows you to recharge the battery pack.

- No brake. The front wheel is not equipped with a brake system. The braking can only be provided at the rear.

Like a handbrake, the rear brake can be drum, electric, or disc. In addition, there may still be a classic foot brake, as in ordinary scooters, or not at all.

— Disk. The disc brake on the rear wheel ensures a quick stop of the scooter. These brakes have a short-stroke friction clutch. Due to the small distance between the pads and the disc, the friction clutch very quickly comes into contact with the working surface of the brake disc. In this case, the friction clutch is pressed against the disk with a sufficiently large force. The disc brake allows the scooter to stop extremely efficiently. But when using a disc brake on the rear wheel, you should be careful, because when braking hard, especially when cornering, the scooter can skid to the side.

- Drum. The drum type brake has above average efficiency. The drum brake makes the rear wheel massive and heavy. This type of brake has a closed design. The pads are inside the wheel. Friction linings rub against the inner surface of the rim. Access to the drum brake is closed by a protective cover. Thanks to the closed design, neither moisture nor other blockages get inside the brake drum, which makes the brake operation more reliable and trouble-free. Among the shortcomings can be noted: an increase in the dimensions and weight of the wheel, the complexity of maintenanc...e.

- Foot. The simplest kind of clamping type brakes, which involves slowing down and stopping the scooter by pressing your foot on the fender of the rear wheel. Note that this is the least efficient braking system of the existing options.

- Electric - braking with the help of recuperation. The brake system of this type makes the stop extremely soft, slowing down occurs when the speed of the electric motor decreases. The rear location of the electric brake assumes that the electric motor is mounted on the rear wheel. The presence of an electric motor makes the wheel massive. The electric type brake system is highly reliable and durable, it does not require maintenance. But if the battery pack on the scooter runs out, the electric brake will not work. For such cases, an additional mechanical (hand or foot) brake is usually provided.

- Absent. The rear wheel is not equipped with a brake. In this case, the braking system is provided at the front. The advantage of scooters without a rear brake is that the vehicle will not skid to the side when braking actively when cornering.

Battery capacity installed in the electric scooter.

Theoretically, a higher battery capacity allows for a longer range, but in fact, not everything is so clear. Firstly, motors of even the same power can differ in efficiency; secondly, the actual amount of energy stored in the battery depends not only on the capacity in amp-hours but also on the voltage in volts. So this parameter is secondary, and when choosing, it is worth focusing not so much on the battery capacity, but on the directly claimed range. You can compare capacity only for models with similar characteristics and the same supply voltage.

In general, this parameter is of secondary importance; in fact, it is needed mainly when looking for a spare / replacement battery or a third-party charger. When choosing, it is worth paying attention to characteristics that are closer to practice - in particular, directly claimed speed and power reserve.

Time to fully charge the battery from zero to 100%.

The more powerful the device, the more capacious batteries it needs and, as a rule, the longer the charging time. In the heaviest models, it can reach 20 hours. However, such indicators are rare - most electric scooters are charged for a maximum of 8-9 hours, which allows you to put the device on charge “from evening to morning”.