Comparison WORKER Junior vs WORKER Kid

The dimensions of the deck in length and width (according to the largest dimensions).

Both small and large decks have their advantages and disadvantages. So, a short and narrow deck contributes to manoeuvrability, but puts forward additional requirements for the rider's skill — it can be difficult to cope with a small "nimble" skate, especially at high speed. A long and wide board, on the contrary, is more stable, but it is difficult to make sharp manoeuvres on such a skateboard. In addition, the optimal length for each type of skate (see above) also depends on the age category of the skater: for example, classic skateboards in the adult version have boards no shorter than 600 mm, and anything less refers to children's models. The width, in turn, can be determined by the size of the foot: a person with a large size (from 44) may simply be uncomfortable on a narrow deck.

Detailed recommendations on the optimal dimensions for each type of skate and planned riding features can be found in special sources.

The number of individual layers of material that make up the deck.

Layered design is used mainly in wooden decks (see "Deck material"); plastic or aluminium usually are made in one piece. The use of several layers allows you to achieve the necessary combination of elasticity for skates with bending strength in any direction. To do this, each layer of wood is laid with fibres in a certain direction.

Theoretically, the more layers, the more directions in which the fibres of the tree are stacked, and the lower the likelihood that the load will go in the “weak”, poorly reinforced direction. In addition, it is multilayer decks that most often have additional inserts that further reinforce the structure (for example, made of carbon). On the other hand, the differences between different models depend much more on the specs of the material than on the number of layers. Therefore, when choosing, it makes sense to pay attention, not so much to this parameter as to more but more obvious specs — primarily the material of the deck and the price category of the product.

Now on the market there are decks made from such several layers: 6 layers, 7 layers, 8 layers, 9 layers, 10 layers.

The diameter of the wheels installed on the skateboard.

The speed reached by the skateboard is directly proportional to the diameter of the wheels, and the acceleration is inversely proportional. In other words , larger wheels will accelerate more slowly, but to higher speeds. Accordingly, when choosing this parameter, it is first of all necessary to take into account what is more important: good speed (for this it is better to choose larger wheels) or the ability to manoeuvre (small ones are suitable for this). In addition, the large diameter makes it easier to cope with small bumps on the road.

It is also worth remembering that each type of skateboard (see above) has its requirements for the size of the wheels, due to the specifics of the application: for example, high-speed longboards have larger wheel diameters than classic stunt skateboards. Accordingly, only models of the same type can be compared with each other according to this parameter. Detailed recommendations on the optimal diameter for different types of skateboards can be found in special sources.

The wheels are usually made removable, which means that if desired, wheels of a different diameter can be installed on the skateboard. However, they should not differ greatly in size from regular ones. You should be especially careful with large wheels: it may turn out that the deck will reach them when tilted, and this is fraught with falls and injuries.

The thickness of the wheels installed on the skateboard.

The width of the wheel is, roughly speaking, the width of the track left during movement. Narrow wheels are convenient for stunts, in particular in grinds (sliding along pipes, railings, etc. directly on the suspension), but they require flat surfaces; wide, in turn, behave better on rough roads, they are more stable and cope with small bumps more efficiently. Accordingly, narrow wheels are typical mainly for stunt models designed for skate parks and other specialized locations with high-quality surfaces; wide, in turn, are better suited for longboards and "city" cruisers who often have to ride on less than perfect roads.

The wheels in modern skateboards are made removable if desired, they can be replaced with wider or narrower ones. However, it is still not recommended to deviate from the “native” width value — riding can become uncomfortable, if not dangerous.

The bearing is responsible for fastening the wheel on the axle, it is thanks to it that the wheel rotates — which means that the characteristics of the wheel rotation directly depend on the characteristics of this part. Without going into technical details, we can say that the class determines, first of all, the accuracy of manufacturing bearing parts. But higher accuracy, on the one hand, reduces friction, making the bearing (and wheel) more fast, on the other hand, it reduces the life of the part and significantly affects its cost. Accordingly, it makes sense to look for high-quality bearings primarily for professional use; and for a simple ride relatively simple options are quite suitable.

Most modern skateboards use ABEC 3, ABEC 5 and ABEC 7 class bearings, which are sufficient for most applications. The minimum class is ABEC 1, which is found mainly in low-cost and children's skateboards. But the super- precision ABEC 9 and ABEC 11 are mainly used in professional longboards, for which high speed is crucial.

Note that most skateboards allow you to replace regular wheels with others with higher-end bearings.