Comparison Samsung HW-C450 vs Samsung HW-S50A

The audio format produced by a sound projector is actually the largest number of individual audio channels supported by the device. Note that in this case we are talking about the number of real channels, that is, channels for each of which at least one speaker is allocated; Models that support virtual surround sound can give the listener the impression of more channels than there actually are (see below for more details).

The sound format is indicated by two or three numbers separated by a dot. The first indicates the number of main channels, the second - the number of subwoofers, the third - the number of additional vertical radiators. For example, 2.1 format corresponds to stereo sound (2.0) supplemented by a subwoofer. And the conditional 3.1.2 format includes left, right and center channels, a subwoofer, left and right vertical speakers.

Sound projectors that support a more advanced sound format than 3.1 are designated in our catalog as multi-channel. The classic multichannel audio format is 5.1, but there are other options. In any case, a large number of real channels contributes to the fidelity of the reproduced sound and simplifies setup compared to virtual surround sound systems, but is also more expensive.

The most common sound formats are: 2.0, 2.1, 3.0, 3.1, 4.1, 5.1, 5.1.2, 7.1.

The total power rating of the sound projector speakers (including subwoofer, if present).

This parameter is often used to estimate the overall sound volume of the device, but this is not entirely true. The fact is that the actual sound volume is determined mainly by the power of the main speakers of the sound projector, and the total power is the sum of this power and the power of the subwoofer. Therefore, models with the same power rating can vary markedly in actual volume: for example, a 150-watt soundbar with a 50-watt subwoofer will be louder than a 100-watt projector with a subwoofer of the same power, although in both cases the rated power will be equal to 200 watts.

Summing up, we can say that it is possible to evaluate the volume by rated power only if the sound projector is not equipped with a subwoofer — in such models, the rated power is equal to the power of the main speakers. In other cases, it is worth focus on the power of the soundbar and the power of the subwoofer directly stated in the characteristics (see below for both).

The nominal power of the speakers installed directly in the soundbar, excluding the subwoofer (in models with a built-in subwoofer, respectively, only the power of the main speakers is taken into account).

This indicator directly determines the overall volume of the sound projector; It is worth choosing according to this parameter taking into account the specifics of the room in which the projector is planned to be installed: the larger the room and the greater the distance to the viewer, the higher the power should be, otherwise the soundbar will not be able to effectively sound the scene. Detailed recommendations on the optimal power for different situations can be found in special sources.

The audio frequency range supported by the projector's speakers.

When evaluating this parameter, it is worth remembering that the audibility range of the human ear is about 16 – 22,000 Hz (and narrows with age). If the projector's frequency range is narrower, this can result in "cutting" low or high frequencies (however, with a slight narrowing, this effect is almost imperceptible). There are models in which the frequency limit is much wider — however, this is a kind of "side effect" of high-quality acoustics and has no meaning other than advertising.

Also note that a wide frequency range in itself does not guarantee high-quality sound — a lot depends on other parameters of the projector.

Impedance is the projector's resistance to alternating current, or more precisely, to the analog audio signal input from an external power amplifier. Actually, this parameter is of practical importance precisely if the device is planned to be used with an external amplifier. Ideally, the projector's impedance should match the impedance for which the amplifier is designed - otherwise, the volume may either decrease (if the impedance is too high), or distortion, overload, and even damage to the acoustics (if the impedance is too low) may occur.

Higher impedance is also thought to reduce the likelihood of interference. However, modern speakers (including sound projectors) have standard impedance values of 4, 6 or 8 ohms - the difference is not so great that the differences in sound quality are noticeable.

The presence of a wireless subwoofer in the design of the sound projector.

Any subwoofer enhances the bass response, delivering rich bass. The advantage of a wireless subwoofer is the ability to install it almost anywhere in the room without the hassle of laying wires — this makes it easier to adjust the sound to specific conditions. In addition, such subwoofers can have a fairly solid speaker size — 200 mm or more (see below for more details). However note that wireless acoustics require their own power source and significantly affect the cost of the projector.

Acoustic design of the subwoofer used by the sound projector.

— Closed type. The simplest design option is a speaker installed in a closed case. Such subwoofers have a relatively low volume, but are distinguished by good sound fidelity and a minimum of distortion.

— Bass-reflex type. Subwoofers equipped with a phase inverter - a special tube connecting the inner volume of the case with the outer space. Such equipment improves the volume and saturation of the sound, but increases the likelihood of interference (primarily the rumble of air in the pipe).

— With a passive radiator. The passive radiator is actually a speaker without a coil and a magnet, installed in the subwoofer cabinet along with the main speaker. The purpose of such a radiator is similar to the phase inverter described above, except that it is less susceptible to interference.

The rated power of the subwoofer included in the design or delivery of the sound projector.

The higher the power, the louder the sub can sound, the richer the bass it can provide. On the other hand, an increase in power inevitably promises an increase in the size and cost of the speaker. Therefore, an overly powerful subwoofer is just as undesirable as one that is too weak. Detailed recommendations for selecting power for the size and acoustic characteristics of a particular room can be found in special sources.

Note that the external subwoofer in soundbars should be approximately twice as powerful as the soundbar in order to prevent sound sags at maximum volume. So, if the total output power of the speaker system is 300 watts, then 100 of them should come from the soundbar alone, and 200 should go directly to the subwoofer.

— Airplay. Wireless technology for connecting an external signal source to the projector. Developed by Apple, it is mainly used to connect with its devices (for example, iPad tablets or MacBook laptops), although it is also used by other manufacturers. AirPlay allows you to transfer not only sound, but also text and graphic information, and even video, which can be useful when connecting the projector to a TV. This technology, by definition, means support for Wi-Fi (see below), because. it is based on this interface.

— Airplay 2. The second generation of the AirPlay technology described above, introduced in 2018. Among the main innovations of this version is support for the "multi-room" format, that is, the simultaneous transmission of several audio signals to different compatible devices installed in different places. In this way, you can, for example, turn on an online broadcast of a news programme in the living room, relaxing music in the bedroom, etc. In addition, AirPlay 2 received a number of other improvements — improved buffering, the ability to stream to stereo speakers, as well as support for voice control via Siri.

— Chromecast. The original name is Google Cast. A technology for broadcasting content to external devices developed by Google. Allows you to transmit an audio signal from a PC or mobile device to the soundbar, the broadcast is standar...dly carried out via Wi-Fi, while the receiver and signal source must be in the same Wi-Fi network (Chromecast media players are an exception). Note that in signal sources (smartphones, tablets, PCs, etc.), Chromecast is implemented at the level of individual applications. For example, at the time of its creation, this feature was available, among others, in the YouTube and Netflix apps for Android and iOS, as well as in the web versions of these apps for Chrome. Thanks to this format, this technology is extremely widespread nowadays, and the ability to connect a particular gadget to an audio system with a Chromecast is usually limited to the ability to install appropriate applications on this gadget.

— Wi-Fi. Wireless technology with multiple applications. One of them is connecting to a computer network; in sound projectors, it is primarily used for local resources (see DLNA below) or AirPlay technology (see above), as well as for controlling the projector over a network. Another option is to connect directly to other devices. The possibilities of such a connection in different models may also be different; one of the most popular options is remote control of the projector from a smartphone, tablet, etc.

— Bluetooth. Wireless technology designed to directly connect different electronic devices to each other. In sound projectors, it is primarily used to broadcast audio wirelessly from another Bluetooth device, such as a smartphone or laptop. However, there may be other options — for example, connecting wireless headphones to the projector itself or remote control from the same smartphone. It is worth noting here that the sound quality when transmitting via Bluetooth is somewhat lower than with a wired connection; on the other hand, this is offset by convenience, and some models of sound projectors may even have a "sound restoration" system.

— NFC. NFC is a wireless communication technology over short distances, up to 10 cm. In sound projectors, it is used mainly as an auxiliary, to facilitate connection via Wi-Fi or Bluetooth. It looks like this: instead of manually digging into the settings, just bring an NFC-compatible device to the projector chip and confirm the connection.

— FM radio. The projector has a built-in FM tuner. This function actually turns the device into a full-fledged radio receiver, allowing you to receive broadcasts on the FM band (which broadcasts most music radio stations). Note that some models with a tuner may support other bands, such as AM or digital DAB.

— LAN. A standard wired connection to a computer network, also known as Ethernet or RJ-45. Like Wi-Fi (see above), in sound projectors it is used primarily for working on a local network; however, LAN capabilities can include both playback of network content via DLNA (see below) and control of projector settings via a network from a computer. A wired connection is not as convenient as Wi-Fi due to the need to run a cable, but it is more reliable and can come in handy when the air is “loaded” (an abundance of Wi-Fi devices nearby).

— DLNA. A technology used to connect various electronic devices into a single digital network with the ability to directly exchange content. Devices for which support for this standard is claimed are able to effectively interact regardless of the manufacturer. And the network itself works on the basis of a conventional computer "local area", connection to it is carried out via LAN or Wi-Fi (see above). In sound projectors, DLNA can be used, for example, to play music from a computer hard drive.

— RS-232. A service interface used to connect the sound projector to a computer and control the sound settings from the PC through a special programme. On some models, it can also be used to update the firmware.

— Connecting an iPod. Special interface for connecting Apple iPod players. Most often it is based on a regular USB connector, to which the player is connected via an adapter cable; however, it may look like a dock — a stand with a proprietary connector, where the gadget is directly placed. Anyway, connecting in this way provides not only playing music from the player, but also other possibilities — for example, switching tracks from the projector's remote control, charging the battery, etc.

— Wireless connection to TV. Ability to connect the sound projector to the TV wirelessly. The advantage of this option is obvious: it eliminates the hassle of additional cables. On the other hand, a wireless connection is usually based on a certain proprietary technology (LG Sound Sync, TV SoundConnect, etc.) and requires a TV that supports the corresponding technology to work. This limits the use of this feature. In addition, such a connection is more susceptible to interference than a wired one, and “wireless” projectors are more expensive than wired ones. Therefore, it is worth specifically looking for a model with such a function if you have a TV with wireless technology support and at the same time the absence of extra wires is fundamental.