Comparison JBL Bar 300 vs Panasonic SC-HTB400

The audio format produced by a sound projector is actually the largest number of individual audio channels supported by the device. Note that in this case we are talking about the number of real channels, that is, channels for each of which at least one speaker is allocated; Models that support virtual surround sound can give the listener the impression of more channels than there actually are (see below for more details).

The sound format is indicated by two or three numbers separated by a dot. The first indicates the number of main channels, the second - the number of subwoofers, the third - the number of additional vertical radiators. For example, 2.1 format corresponds to stereo sound (2.0) supplemented by a subwoofer. And the conditional 3.1.2 format includes left, right and center channels, a subwoofer, left and right vertical speakers.

Sound projectors that support a more advanced sound format than 3.1 are designated in our catalog as multi-channel. The classic multichannel audio format is 5.1, but there are other options. In any case, a large number of real channels contributes to the fidelity of the reproduced sound and simplifies setup compared to virtual surround sound systems, but is also more expensive.

The most common sound formats are: 2.0, 2.1, 3.0, 3.1, 4.1, 5.1, 5.1.2, 7.1.

Regular way to install a sound projector.

— Shelf. The installation itself on the shelf is extremely simple and requires a minimum of effort. However, in the absence of a shelf in a suitable place, you will either have to hang it there (for which, most likely, you will need to drill the walls), or install the projector "where possible" and try to adjust the sound as needed (and the success of such a setup is not guaranteed).

— Wall mounted. Projectors equipped with wall mounts, usually in the form of brackets or notches in the chassis for nails, screws, or other wall-mounted mounts. This option is good because you can choose the installation location of the projector at your discretion, not limited to the presence of shelves — the main thing is that there is a free wall.

— Shelf / wall. Projectors that can be either shelf-mounted or wall-mounted. Both of these options are described above. Here we note that the installation method determines not only the design of the case, but also some features of the sound produced by the projector. In fact, this means that a “pure wall” projector, when installed on a shelf, will not be able to produce sound of proper quality, even if there are no problems with the installation itself. In other words, if you need a device suitable both for a shelf and for hanging on a wall, you should choose from models for which such a possibility is direc...tly stated.

— TV Stand. In fact, such models are a variation of the shelf projectors described above, which have a flat body, so that a TV can be installed on top of such a device. This will prevent the sound projector from obscuring the controls and remote control sensor located below the screen (whereas with conventional shelf models, such problems often occur when placed on the same shelf with a TV). The disadvantage of "stands" can be called a rather large size in depth.

The ability of the projector to output a video signal in Ultra HD (4K) resolution — 3840x2160. This is the highest resolution used in modern consumer video equipment — 4 times higher than Full HD. However, note that this feature significantly affects the price of the projector, and to view such a video signal, you will need an appropriate screen. Therefore, it makes sense to specifically look for an UltraHD device only if you initially plan to connect it to a screen of the appropriate resolution.

This feature requires the projector to have at least one HDMI output (see below). In this case, the video signal source can be either an external device or the projector itself, operating in the format of a media centre (for example, a model with direct playback from USB media).

The total power rating of the sound projector speakers (including subwoofer, if present).

This parameter is often used to estimate the overall sound volume of the device, but this is not entirely true. The fact is that the actual sound volume is determined mainly by the power of the main speakers of the sound projector, and the total power is the sum of this power and the power of the subwoofer. Therefore, models with the same power rating can vary markedly in actual volume: for example, a 150-watt soundbar with a 50-watt subwoofer will be louder than a 100-watt projector with a subwoofer of the same power, although in both cases the rated power will be equal to 200 watts.

Summing up, we can say that it is possible to evaluate the volume by rated power only if the sound projector is not equipped with a subwoofer — in such models, the rated power is equal to the power of the main speakers. In other cases, it is worth focus on the power of the soundbar and the power of the subwoofer directly stated in the characteristics (see below for both).

The nominal power of the speakers installed directly in the soundbar, excluding the subwoofer (in models with a built-in subwoofer, respectively, only the power of the main speakers is taken into account).

This indicator directly determines the overall volume of the sound projector; It is worth choosing according to this parameter taking into account the specifics of the room in which the projector is planned to be installed: the larger the room and the greater the distance to the viewer, the higher the power should be, otherwise the soundbar will not be able to effectively sound the scene. Detailed recommendations on the optimal power for different situations can be found in special sources.

The audio frequency range supported by the projector's speakers.

When evaluating this parameter, it is worth remembering that the audibility range of the human ear is about 16 – 22,000 Hz (and narrows with age). If the projector's frequency range is narrower, this can result in "cutting" low or high frequencies (however, with a slight narrowing, this effect is almost imperceptible). There are models in which the frequency limit is much wider — however, this is a kind of "side effect" of high-quality acoustics and has no meaning other than advertising.

Also note that a wide frequency range in itself does not guarantee high-quality sound — a lot depends on other parameters of the projector.

Impedance is the projector's resistance to alternating current, or more precisely, to the analog audio signal input from an external power amplifier. Actually, this parameter is of practical importance precisely if the device is planned to be used with an external amplifier. Ideally, the projector's impedance should match the impedance for which the amplifier is designed - otherwise, the volume may either decrease (if the impedance is too high), or distortion, overload, and even damage to the acoustics (if the impedance is too low) may occur.

Higher impedance is also thought to reduce the likelihood of interference. However, modern speakers (including sound projectors) have standard impedance values of 4, 6 or 8 ohms - the difference is not so great that the differences in sound quality are noticeable.

The presence of a built-in subwoofer in the design of the sound projector.

Any subwoofer enhances the bass response, delivering rich bass. Models with a built-in subwoofer are more convenient to install and take up less space, because. no need to look for a separate place for the woofer. On the other hand, the dimensions of this speaker are usually smaller than those of a separate subwoofer (this is due to the limited space in the projector cabinet) — accordingly, the bass is less powerful and richer.

Acoustic design of the subwoofer used by the sound projector.

— Closed type. The simplest design option is a speaker installed in a closed case. Such subwoofers have a relatively low volume, but are distinguished by good sound fidelity and a minimum of distortion.

— Bass-reflex type. Subwoofers equipped with a phase inverter - a special tube connecting the inner volume of the case with the outer space. Such equipment improves the volume and saturation of the sound, but increases the likelihood of interference (primarily the rumble of air in the pipe).

— With a passive radiator. The passive radiator is actually a speaker without a coil and a magnet, installed in the subwoofer cabinet along with the main speaker. The purpose of such a radiator is similar to the phase inverter described above, except that it is less susceptible to interference.