Comparison surge Protectors & Extension Leads

The general features of the design and application of the network filter depend on the type.

— Extension lead. Traditional extension cords designed to bring power to devices located far from outlets, as well as to increase the number of sockets themselves. They do not have built-in filters and provide almost no protection. On the other hand, such devices are extremely simple and inexpensive.

— Cable reel. Extension cords in which the wire is wound on a spool. They are significantly longer than models without coils; in addition, the user can adjust the length of the wire at his discretion. On the other hand, the weight and dimensions of such devices are also quite significant. As a result, extension cords on a reel are not well suited for home use, but may be indispensable for some specific tasks. For example, using such a device, you can stretch power through the yard of a private house, for work in a garage or a barn.

— H-frame extension lead. Extension cords in which the wire is wound around the frame — a special holder that resembles a double-sided horn. The design of the frame itself allows you to conveniently unwind and wind the power cord, while the wire is not subjected to twisting into knots and tangles. The extension cord on the frame usually has only one socket for connecting an electric current consumer.

— Roulette ex...tension lead. A kind of extension cord with a round body, in which the cord is wound in the manner as it is implemented in construction roulettes. In its upper part there are sockets (their number and type may differ), and on the reverse side there is a handle for returning the cord to the case. There is no automatic winding of the cord on the coil inside the case.

— Surge protected adapter. The simplest type of network filters are compact devices that are attached directly to the outlet. The possibilities of such devices are extremely simple: other connectors, in addition to ordinary sockets, are extremely rare in them, and the sockets themselves are usually provided with less than one (although exceptions are possible). On the other hand, small size in some situations can be an important advantage. In addition, such a filter can be constantly worn on the plug of the device with which it is used.

— Surge protector. Devices that combine the functions of a surge protector and an extension cord: allow you to connect electrical appliances to the network that are remote from outlets, while smoothing out the interference that occurs on the network. In addition, most models have several outlets, which allows you to connect several devices to one such filter at once. Note that models with 3-5 outlets are very popular as a means of connecting desktop PCs to a network: they allow you to power both the system unit and peripherals (monitor, speakers, printer, etc.) and additional devices like a table lamp from one outlet .

— Surge protector reel. Network filters equipped with a wire reel. According to the features of the application, they are completely similar to the extension cords on the reel described above, adjusted for the fact that in this case the device not only works as a remote outlet, but also protects the load from interference in the network.

The length of the cable used to connect the surge protector to the network.

The longer the cable, the farther from the outlet you can install the device. On the other hand, a long cable can be inconvenient over short distances. Models on a coil are deprived of this drawback (see "Type"), this moment is compensated by the actual presence of the coil, but they differ in large dimensions and heavy weight. So when choosing, it is far from always worth chasing the maximum length of the wire.

The highest power consumption of the connected devices that the surge protector can tolerate without consequences (to be more precise, with which it can work indefinitely without overloads, overheating, etc.).

This limitation is due to the fact that the higher the power at the same voltage, the higher the current passing through the equipment (in this case, through the surge protector); and off-design currents can lead to breakdowns and even accidents. And although in order to avoid these consequences, modern filters often provide various types of protection (see above), however, the operation of protection is still an emergency situation that is best avoided. Therefore, it is worth choosing a model according to this parameter in such a way that the maximum filter power is at least not lower than the total power consumption of the load. And it is best to have a margin of 20 – 30% — this will give additional guarantees in case of various deviations in the operation of the connected equipment.

Separately, it is worth highlighting the situations when the filter is planned to be used for the so-called reactive load — electrical appliances that widely use circuits on capacitors and/or inductors, for example, power tools or refrigeration units. The total power consumption of such devices (written in volt-amperes) can be much higher than the active power (which is indicated in watts). The recommended line filter power in such cases is calculated using special...formulas that can be found in the relevant sources.

The maximum current that the surge protector can pass through itself for an unlimited time without the risk of overheating, breakdowns and other troubles.

This parameter is directly related to the maximum power of the filter (see above): power is the current multiplied by the voltage. Thus, for example, for a standard 230 V model with a maximum power of 2200 W, the maximum load will be 10 A. Note that the characteristics of modern filters may not correspond to such calculations — for example, the same 10 A can be claimed for a 2500 W model . However, this is not something extraordinary: the difference in figures may be due to active and reactive power (see "Maximum power"), the characteristics of single-phase filters (without 400 V sockets, see above) can be given both for 230 V, so for 230 V and even 240 V, figures may be rounded for readability, etc.

Anyway, the practical value of the maximum load is the same as the maximum power: it should not be less than the current supplied to the connected electrical appliances (otherwise the protection may trip, or even break). And they use this parameter, along with the maximum power, because in some cases it is easier to evaluate the characteristics of the load (and filter requirements) in terms of current consumption, and not in terms of power.

The maximum energy absorption provided by the mains filter, namely, the maximum pulse energy at which the device can safely absorb and dissipate it, completely protecting the connected load. The higher this indicator, the more reliable the filter, the more powerful power surges it can handle. In inexpensive models, the maximum absorption is calculated in tens of joules, in the most advanced models it can exceed 1000 J and even 2000 J.

The cross-sectional area of the wire used to connect the filter to the network. The larger the cross-sectional area, the thicker the wire, the more reliable it is and the more current it can pass without overheating. Accordingly, thick wires ( 1.5 mm² and 2.5 mm²) are a must for high power devices. At the same time, modern manufacturers, usually, choose the cross-sectional area in such a way as to guarantee the safe operation of the filter at the claimed maximum power (see above). Therefore, in fact, a model with a thicker cable than other similar devices should be chosen if it is supposed to be used in unstable networks in which power surges often occur. If the cross-sectional area seems too small for you ( 0.75 mm² or 1 mm²) for the claimed power, there are special formulas that allow you to check the validity of such doubts.

The presence in the design of the surge protector of a special indicator (usually in the form of a light bulb) that indicates that the device is turned on.

This function provides the presence of at least one common indicator; and on models with switches per outlet (see below), additional indicators can be installed on the outlets. Anyway, such equipment makes working with the surge protector more visual, allowing you to immediately assess the status of the device and avoid some unpleasant situations (for example, imaginary equipment breakdowns — when a “faulty” device does not work just because the filter is not turned on).

The indicator can be installed directly in the switch (general or for each outlet, see the relevant paragraphs for details).

— Switch on the body. This function allows you to turn off the power to the load without disconnecting the filter itself from the mains — in other words, it eliminates the need to once again remove the filter plug from the outlet and insert it back. Most often, the switch controls all filter outlets, however, there are models where some of the connectors are bypassed and are always energized, regardless of the position of the switch.

— A switch for each outlet. This feature makes it easier to manage the power of connected devices: unplugging and plugging individual outlets is usually easier and faster than unplugging and plugging back in. Thus, electrical appliances used with such a filter can be kept constantly connected to it, turning off and on individual outlets as needed.

— Switch for each circuit. The function is used in models with numerous outlets. Allows you to simultaneously disable half of them, leaving the rest working. It combines the convenience of the points listed above and at the same time does not clutter up the device with unnecessary switches.

It is also worth noting that there are models that combine both a switch on the case and a switch for each outlet.

The type of plug (plug) used to connect the surge protector directly to the network.

— Normal. A traditional plug for sockets, which is standardly used in Europe and the post-Soviet space. The official name is CEE 7/4, or Schuko. If the filter is planned to be connected directly to a regular household network, you should pay attention to this type of plug. Also note that in models with 400V outlets (see below), a normal plug refers to a standard 400V plug.

— UPS (for UPS). A plug designed to fit into a three-prong IEC 60320 C13 socket, also known as a "computer socket". Such connectors are often found in uninterruptible power supplies, but they are practically not used as ordinary power outlets. Therefore, buying a filter with such a plug makes sense only if it is planned to be used in combination with a UPS.