Drum volume
The internal volume of the dryer drum.
A
larger drum can accommodate more laundry, but there is no rigid dependence here: models with the same volume may differ in maximum load. It is because to process a large mass of laundry, one need not only a capacious drum but also an engine of appropriate power. At the same time, in a larger drum, the same mass of laundry will dry more efficiently than in a small one, because laundry will be more freely distributed over the drum, crumpled less, and warm air will better penetrate the folds of the fabric. As a result, for the same drum volume, a model with a smaller load will be more efficient and performant than a model with a larger load. On the other hand, a volumetric drum takes up more space and the dimensions of the dryer are largely determined by the dimensions of the drum.
Refresh cycle
A programme designed to remove odours from clothes, such as tobacco smoke, or an unpleasant odour that appears after a long period of storage.
The refresh programme is useful if the clothes are clean, but the smell still needs to be eliminated — refreshing in the dryer takes less time and effort than quick washing and then drying (even if using the same dryer). This function is especially relevant for
drying cabinets.
Drying class
Drying class describes the overall drying efficiency that the machine provides. It is denoted by a Latin letter, where A is the best efficiency, and further in decreasing order (
drying class B is inferior to
class A, but exceeds
class C). Naturally, higher efficiency machines cost more (ceteris paribus).
Energy class
The energy consumption class shows not the actual energy consumption but the efficiency of the dryer. In other words, what part of the electricity consumed goes directly to useful work. For dryers, this parameter is especially important because such devices have high electricity consumption. As a result, models with the same capabilities but different energy efficiency classes differ markedly in terms of operating costs (in terms of electricity bills). However, more economical units themselves are more expensive. nevertheless, this difference quickly pays off.
Initially, classes were marked in Latin letters from
A(the highest class) and further alphabetically. In the course of technology development, more economical levels of consumption than the original class A appeared — they are labelled as A+,
A++, A+++, etc. Actually, the highest efficiency class in modern dryers is exactly
A +++ ; level A —
A+ can be called good,
B — average, C — acceptable.
Controls
The type of control provided in the machine. Almost all modern dryers are equipped with electronic control, so the design of the control panel mainly depends on this parameter. The options here might be:
—
Rotary knob + buttons. The classic option does not lose popularity these days. The rotary knob is usually responsible for selecting the programme and the buttons for controlling additional functions and settings. Such control panels are simple, inexpensive and, at the same time, quite functional. Therefore they are found in all categories of dryers — from low-cost to top.
—
Rotary knob + touch controls. The combination of a rotary knob responsible for selecting the main programme and a set of touch controls that control additional parameters. Compared to the buttons described above, the touch panels have a more stylish and technological appearance; moreover, due to the absence of protruding parts, such a panel almost does not accumulate dirt and is easy to clean. At the same time, these features are generally not fundamental, while the touch controls are somewhat more complicated and expensive than buttons. Therefore, this option is found mainly among dryers of the middle and top classes.
—
Touch controls. This design, on the one hand, gives the device the most accurate and advanced appearance; on the other hand, the control is not as cle
...ar and intuitive as with a handle. Therefore, in its pure form, touch controls are extremely rare — only in high-end dryers.Country of origin
The country in which, according to the manufacturer, the model is manufactured. Despite the fact that most of the capacities are concentrated in
China, European factories (in
Germany,
Poland,
Slovenia,
Turkey, etc.) for the production of household appliances have not gone away. And certain models can be produced there. In general, such a division into a Chinese or European factory should not particularly affect the quality of products, but the stereotype of a reliable European assembly is present in us. However, it is possible that the model may have a country of manufacture, for example, Poland, and in the store under the same article, you will meet China.
