Comparison Tasco 3-7x28 vs Tasco Rimfire 3-7x20

The diameter of the objective is the front lens of the sight. This parameter is also called "aperture".

This parameter is important primarily for optical sights and their specialized varieties — "night lights" and thermal imagers (see "Type"). The larger the lens, the more light enters it, the higher the image quality and the more efficient the device will work in low light, but the more expensive such optics will cost. It is worth noting here that the requirements for the aperture also depend on the degree of magnification: in other words, especially large lenses are not required for low magnifications. Therefore, relatively small entrance lenses, with a diameter of 25 – 35 mm and even less, are found in all price categories of classical optics — from low-cost to top. And you can compare by aperture only models with the same maximum magnification, and even then it’s very approximate — it’s worth remembering that image quality also depends heavily on the overall quality of the sight components.

In turn, for night sights, especially those based on image intensifier tubes (see "The principle of operation of night vision devices"), a large aperture is fundamentally important. So a diameter of 36 to 45 mm is considered very small for such devices and is found only in some digital models, while most nightlights are equipped with lenses of 46 mm or more.

As for collimators, the size of the space that enters the scope depends mainly on the aperture. Moreover, the actual visible size can be changed by setting the sight closer or farther to the eye — the principle of operation of collimators makes this possible. Note also that for models with lenses of a rectangular or similar shape, the size of the lens is usually indicated diagonally.

The diameter of the exit pupil created by the optical system of the sight.

The exit pupil is called the projection of the front lens of the lens, built by the optics in the region of the eyepiece; this image can be observed in the form of a characteristic light circle, if you look into the eyepiece not close, but from a distance of 30 – 40 cm. The diameter of this circle can be calculated by dividing the lens diameter by the multiplicity (see above). For example, an 8x40 model would have a pupil diameter of 40/8=5mm. This indicator determines the overall aperture of the device and, accordingly, the image quality in low light: the larger the pupil diameter, the brighter the “picture” will be (of course, with the same lens quality, because it also affects the brightness).

In addition, it is believed that the diameter of the exit pupil should be no less than that of the pupil of the human eye — and the size of the latter can vary. So, in daylight, the pupil in the eye has a size of 2-3 mm, and in the dark — 7-8 mm in adolescents and adults, and about 5 mm in the elderly. This point should be taken into account when choosing a model for specific conditions: after all, high-aperture optics are expensive, and it hardly makes sense to overpay for a large pupil if you need a scope exclusively for daytime use.

The offset is the distance between the eyepiece lens and the exit pupil of an optical instrument (see "Exit Pupil Diameter"). Optimum image quality is achieved when the exit pupil is projected directly into the observer's eye; so from a practical point of view, offset is the distance from the eye to the eyepiece lens that provides the best visibility and does not darken the edges (vignetting). A large offset is especially important if the sight is planned to be used simultaneously with glasses — after all, in such cases it is not possible to bring the eyepiece close to the eye, and it must be at some distance from the glasses so as not to hit the glass due to recoil.

The diameter of the area visible through the sight from a distance of 100 m — in other words, the largest distance between two points at which they can be seen simultaneously from this distance. It is also called "linear field of view". This indicator is more convenient for many users than the angular field of view (the angle between the lines connecting the lens and the extreme points of the visible image) — it very clearly describes the capabilities of the device.

In sights with magnification adjustment (see above), both the entire range of width — from maximum to minimum — or only one value of this parameter can be indicated. In the latter case, the largest width of the field of view is usually taken, at the minimum magnification.

A complex indicator that describes the quality of any optical system (including sights) at dusk — when the lighting is weaker than during the day, but not yet as dim as in the deep evening or at night. It is primarily about the ability to see small details through the device.

The need to use this parameter is due to the fact that twilight is a special condition. In daylight, the visibility of small details is determined primarily by the magnification of the optics, and in night light, by the diameter of the lens (see above); at dusk, both of these indicators affect the quality. This feature takes into account the twilight factor. Its specific value is calculated as the square root of the product of the multiplicity and the diameter of the lens. For example, for an 8x40 scope, the twilight factor would be the root of 8x40=320, which is approximately 17.8. Models with adjustable magnification (see above) usually indicate the minimum twilight factor corresponding to the minimum magnification.

The lowest value of this parameter for normal visibility at dusk is considered to be 17. At the same time, it is worth noting that the twilight factor does not take into account the actual light transmission of the system — and it strongly depends on the quality of the lenses, the use of antireflection coatings (see below), etc. Therefore, the actual image quality at dusk for two models with the same twilight factor may differ markedly.

One of the parameters describing the quality of visibility through an optical device in low light conditions. Relative brightness is denoted as the diameter of the exit pupil (see above), squared; the higher this number, the more light the sight lets through. At the same time, this indicator does not take into account the quality of the lenses and their coatings used in the design. Therefore, comparing two sights in terms of relative brightness is only possible approximately, because even if the values are equal, the actual image quality may differ markedly. Also note that it makes sense to pay attention to this parameter only if the sight is planned to be used at dusk.

As for specific values, in the "dimest" models, the relative brightness does not exceed 100, in the most "bright" it can be 300 or more. Detailed recommendations regarding the choice of this parameter for certain conditions can be found in special sources. Here it is worth mentioning that the relative brightness is not directly related to the price category of the sight: models similar in this indicator can vary significantly in price.

Units of measurement of angles used in the scope - primarily for making corrections using the drums. The same units are often used in marking the goniometric elements of the aiming reticle (see “Measuring units of the reticle”), but there are exceptions, so it would not hurt to clarify this point separately. Nowadays there are two main units:

- MOA. Abbreviation for minute of arc - 1/60th of a degree. Originally, this unit is associated with the English system of measures and is convenient primarily for calculations in yards and inches: at a distance of 100 yards, an angle of 1 MOA corresponds to a linear dimension of approximately 1 ". In the metric system, which is more familiar to us, this gives 2.91 cm at a distance of 100 m. We also note that this unit is a kind of accuracy standard: it is believed that a full-fledged sniper rifle should give a spread of no more than 1 MOA.

—MRAD. The symbol for a milliradian is an angle of one thousandth of a radian (approximately 0.06°). Also in sniper jargon, this unit is called “thousandth”, or “mil”. It is already tied to the metric system: at a distance of 100 m, an angle of 1 MRAD corresponds to a linear dimension of 10 cm (approximately 3.5 times more than 1 MOA).

The choice based on this indicator largely depends on the personal preferences of the shooter. And although “thousands” are generally more convenient for domestic use...rs, with minimal experience you can successfully use MOA, and also switch between these units and convert one to another without much difficulty. So in general this point is not particularly important.

The division value of the turrets used in the sight to enter corrections.

The increment value for the correction turret is the angle that the point of impact shifts when rotated by 1 click (“click”). In this case, this angle is indicated in MOA — minutes of arc. For more information about this unit, see "Measuring units of the sight"; and the lower the division value, the more accurately you can set up the sight initially and make corrections in the future. For example, if this indicator is 0.5 MOA — each click will shift the point of impact by about 1.46 cm for every 100 m of distance (that is, 2.91 cm at a distance of 200 m, 4.4 cm at 300 m and so on); and 0.25 MOA will already give only 7.3 mm per click for every 100 m.

The smaller the step and the more accurate the adjustment system, the more expensive it is. Therefore, when choosing, it is worth taking into account the features of the planned application — first of all, the size of the targets and the distance to them; detailed recommendations on this matter are in various manuals on shooting. If we talk about specific values, then the mentioned 0.5 (1/2) MOA are typical mainly for inexpensive and medium scopes, 0.25 (1/4) MOA is a pretty good indicator, and the advanced optics itself allows adjustment in increments of 0.125 (1/8) MOA.

A type of coating used in scope lenses. Anyway, we are talking about the so-called antireflection coating, which is the thinnest film (single or multilayer) on the surface of the lens in contact with air. The properties of this film are chosen in such a way as to minimize the reflection of light from the glass surface. The meaning of this function is not so much to reduce the brightness of glare that can unmask the shooter, but to increase the light transmission of the optics and, accordingly, the quality of the image visible through it.

Modern sights can be equipped with the following types of coatings:

— Illuminating. In this case, the simplest option is implied — an incomplete single-layer coating. The term "incomplete" means that not all lens surfaces are coated (although there may be several coated surfaces). Such enlightenment is inexpensive, however, the image quality is relatively low — in particular, because a single-layer film is most effective only for a part of the visible colour spectrum.

— Full illumination. Fully coated means that all surfaces of the lenses that come into contact with air have a special coating; in this case it is single layer. Such a coating is more expensive than a simple anti-reflective coating, but the quality of the “picture” when using it is higher, because. light distortion at the transitions between glass and air is minimized.

— Multi-layered illuminating. Incomplete AR coating (see above)...using multilayer films. Thanks to multiple layers, the anti-reflective coating covers the entire visible spectrum, which allows you to achieve a brighter image with less colour distortion compared to single-layer coatings; However the price of such devices is higher.

— Full multilayer enlightenment. The most advanced option: multilayer coating on all lens surfaces used in the design of the sight. Features of full and multi-layer coating are described separately above. Here we note that their combination is typical for high-class sights, because. it provides the highest quality image, but it is not cheap.