Comparison Beike Q-162A vs Manfrotto MKELMII4CMB-BH

The minimum height relative to the base at which the tripod base can be mounted.

The lower the minimum height, the better the tripod is suitable for macro and product photography; in addition, the range of height adjustment available to the user depends on this indicator. Note that for models with the ability to flip the boom (see below), the minimum height is given for the traditional position of the boom, platform up. And if the claimed minimum is significantly less than the length of the tripod when folded (for example, 15 cm with a length of 50 cm), this means that the legs can “spread” to a horizontal position or close to it, thus lowering the entire structure.

The maximum height from the base on which the tripod base can be mounted.

For desktop use (see "Installation"), a large height is not required, therefore, in most of these models, this figure does not exceed 20 cm — the only exceptions are some specific monopods. Accordingly, the difference in height between different desktop structures in most cases does not matter much. But in the floor models, the most "undersized" have a maximum height of about 40 – 50 cm, and the highest ones are able to open up to 2.5 m and even higher. In such cases, the choice should take into account the specifics of use. So, it makes sense to specifically look for a model at 150 – 160 cm if it is fundamentally important to install the camera at eye level (eye level is usually about 10 cm lower than a person’s height). At the same time, most camcorders and many cameras have swivel screens that allow you to comfortably look at the device from top to bottom; and even in the absence of such a screen, bending down to the level of the camera is not so difficult. And it makes sense to pay attention to tripods with a height of 170 cm and above mainly in those cases when shooting over heads is planned — for example, reports from public events.

The diameter of the centre shaft of a tripod or the main shaft of a monopod (see "Type"). In both cases, thicker rods increase the weight and dimensions of the structure, but have a positive effect on strength. And for classic tripods, a lot of weight can be an advantage — a massive rod has a positive effect on stability, especially in the lowered position.

The type of head provided in the tripod is, in fact, the type of mechanism responsible for rotating the platform with the camera relative to the base.

— 2D. Such heads have 2 degrees of freedom and allow you to turn the camera from side to side and tilt back and forth. At the same time, a separate rotation mechanism is provided for each of the two axes. This makes it easy to shoot vertical and horizontal panoramas: the camera on such a tripod can turn strictly along one of the axes without unnecessary movements that spoil the picture (for example, strictly to the side without moving up and down). Such heads are considered suitable primarily for video filming; for photography, they are somewhat less convenient, but they are still found in photo tripods (including highly specialized ones).

— 3D. Heads with three degrees of freedom: turn from side to side, tilt up and down and “roll” right and left; a separate hinge is responsible for each of the three. They are mainly used in models with the ability to install cameras: such freedom of movement is important primarily for photography. However, specialized tripods for video cameras with 3D heads are also produced. Compared to ball heads (see below), which also provide a high degree of freedom, 3D mechanisms are more accurate, they are indispensable in cases where you need to clearly control the rotation along one axis (when shooting panoramic...or shooting with a rotation effect). On the other hand, 3D heads are more complex and expensive, and also less suitable for quickly pointing the camera in an arbitrary direction.

— Ball. In heads of this type, the platform is attached to the ball by means of a rod, which is clamped in a special mount. By loosening the mount, you can rotate the camera horizontally, as well as arbitrarily tilt back and forth and left and right. The key advantage of such mechanisms is the ability to quickly change the position of the camera; in 3D heads (see above) it takes longer. Also, the advantages of ball heads include simplicity, compactness and low cost. On the other hand, it is difficult to turn the camera on such a head strictly along one axis without moving along the other two, which makes some shooting techniques difficult. In advanced tripods, additional equipment may be provided that partly eliminates this drawback — for example, a separate hinge for horizontal panoramas; however, in terms of accuracy, ball heads are still inferior to 3D mechanisms.

The maximum camera weight that this tripod can support.

If the tripod is purchased for use with a smartphone or action camera, you can ignore this parameter: the weight of such gadgets usually does not exceed 200 g, any tripod of the corresponding specialization can easily handle such a load (see "By Purpose"). Compact point-and-shoot cameras usually weigh up to 300 g, and amateur video cameras - up to 700 g; but in both cases, there are also more massive models. This should be taken into account when choosing a tabletop tripod (see "Installation") for such equipment - some tabletop models have rather limited weight restrictions; but with floor-standing ones, there are usually no difficulties.

But if a tripod is purchased for professional equipment, special attention should be paid to the permissible weight. Thus, a professional video camera can “pull” 2.5 kg or even more; the average weight of a SLR camera is 600 – 800 g, but this is only the “body”, to which the weight of the optics is added – and in some powerful telephoto lenses it can exceed 2 kg. So such devices may require quite “durable” tripods.

Tripod head included. Most often, the head is supplied as a kit, however, some models (mainly professional level) do not come with a head — it is purchased separately and selected for the specific needs of the user (for more details, see "Removable head" and "Head type"). Therefore, in the characteristics of the tripod, this parameter is indicated separately.

The tripod has a camera remote control. The device and functions of such a remote control may be different, depending on the purpose (see above). So, in models for phones and action cameras, compact wireless remote controls are most often provided, which are responsible only for the most basic commands — taking photos and start-stop video recording. Such key fobs are connected to the gadget itself, usually via Bluetooth; with smartphones, this usually does not cause problems, but compatibility with a specific action camera should be specified separately. In turn, advanced video camera tripods can have a wired remote control built right into the head rotation handle — it allows you to control shooting parameters (zoom, focus, etc.), while maintaining full control over the position of the camera.

The main material used in the construction of the body or legs (depending on the type) of a tripod.

— Plastic. The main advantage of plastic is its low cost, due, among other things, to ease of processing and suitability for creating parts of complex shape. In addition, this material can be flexible, have any colour, and even become transparent. On the other hand, its strength is significantly lower than other tripod materials; it is more than enough to work with light weight, however, plastic is not suitable for supporting massive equipment and creating long supports that are subject to significant bending loads due to the large length. Therefore, the main scope of this material today are clamps and small table stands, including flexible design (see "Type").

— Aluminium. Aluminium-based alloys have a combination of high strength and low weight, making them well suited for the construction of tripods of any format — including and classic full size. The cost of this material, however, is somewhat higher than that of plastic and steel, but not by much, and the mentioned advantages more than cover this drawback. Because of this, this material is the most popular in modern tripods, it is widely used in almost all types and price categories.

— Steel. Steel is characterized by high strength — even higher than that of...the aluminium alloys described above, at a slightly lower cost. At the same time, this material has a rather large weight. On the one hand, this contributes to stability, on the other hand, it makes it difficult to carry from place to place. And although the latter is relevant mainly for floor tripods (see "Installation"), however, even in compact desktop models, steel is still rarely used.

— CFRP. The most advanced of the materials used for modern tripods. Carbon fibre, or carbon fibre, is a composite composition of carbon fibers filled with a filler — usually a special resin. In terms of strength characteristics, this combination is comparable to steel, while this material weighs very little, which is especially useful for full-size tripods. Its main disadvantage is the high cost, which is why professional premium models remain the prerogative of carbon fibre. In addition, carbon fibre requires fairly careful handling due to its sensitivity to point impacts — cracks easily appear from them.

— Metal. This option is indicated in cases where the manufacturer, for one reason or another, did not specify the composition of the metal in the characteristics. Most often, this refers to aluminium or steel, the properties and features of the use of both are described above; however, other types of metal may occur. Anyway, when assessing the reliability and durability of such a tripod, it is best to focus on its price category.

— Carbon. Another name for the CFRP described above; used by some manufacturers for the sake of brevity and "solidity of sound".