AEG MF1400KE (4935411850)
 | Outdated Product Type: vertical; Power source: mains (230 V); Power (W): 1400; Max. speed (rpm): 23000; Max. collet diameter (mm): 12; soft start; speed control; LED light; template guide; safety limiter; guide rail; case (bag); E-Catalog uses affiliate links compensated by our partners. |
AEG MF1400KE | |||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||
Always clarify the specifications and configuration of the product with the online store manager before purchasing.
Catalog AEG 2026 - new arrivals, bestsellers, and the most relevant models AEG.
Clinics are the main base, it is difficult and inconvenient to work when setting the working height of the cutter. On the main and additional bases it is not convenient to adjust the micro settings; it feels like the adjustment knobs are designed for the imperial system of units, they are simply erased and metric ones are applied, because of this you need to rack your brains to adjust it down to the millimeter. A large set, starting with an additional base for storage and transport bags. Not big but not small either, for home or mobile work it is not bad. The main base throws, you need to put in effort, and the micron setting is not designed for the metric unit of measurement, you need to additionally load your head. use AEG MF1400KE more than year |
When purchasing, check the flatness of the plunge base base (often very crooked), as well as the heating of the bearing in the collet area The milling cutter is not bad but needs improvement Crooked sole, strong heating of the bearing even at idle use AEG MF1400KE less than month |
The plunge base jams, instead of normal operation you encounter difficulties in work and communication with the service center "Virok com.ua" where they will tell you that incorrect efforts were applied, which caused the guides to bend and the bushings to wear unevenly (while the plunge base was used for about 20 presses with an 8mm groove cutter in pine). Guides cost 1800 UAH, the bare base with bushings around 3000 UAH. In box Submersible base use AEG MF1400KE month or more i recommend it don't buy |
Copy base for working on a template
Profiling wood, milling edges, grooves, ledges, grooves, chamfering — all this is within the power of the AEG MF1400KE router. A distinctive feature of the router is the presence of a copy base. It allows you to work with copy sleeves of different diameters, which in turn are convenient for milling according to the template. By the way, the kit already comes with 5 such bushings for different cutters (17, 24, 27, 30 and 40 mm). You can adjust the rotational speed using the wheel on the housing in the range from 10,000 to 23,000 rpm. Moreover, thanks to the “soft start” of the device, damage to the working material is excluded.
Excellent dust extraction
The model is additionally equipped with a teardrop-shaped sole. At the end of the sole there is a rubberized handle, holding which, it will be easier for the operator to guide the router along the figured pattern. A good view of the milling line is provided by the backlight, and a transparent protective "curtain" protects the eyes from dust and allows you to see the cutter itself. The dust removal system is very well thought out in the router: three nozzles are included in the kit, which can be connected from below, behind or on the side of the router, depending on the work performed. The router itself and all accessories are placed in a bag that is attached to the product. However, the quality of the bag is rather mediocre and its convenience is very different from plastic cases for such a tool.
Milling at serious depth
Milling depth can be adjusted from 1 to 64 mm, which is a pretty decent value for a plunge router. For the most accurate setting of the cutter immersion, there is a regulator under the depth gauge, by turning which you can lower or raise the limiter (every 90 degrees of rotation raises / lowers by 0.4 mm). The milling cutter has powerful springs installed inside the guides, which can shoot when the device is released. To prevent this from happening, a restrictive pin with a nut is wisely thought out in the design, which can be adjusted exclusively for yourself. Of course, for all this excellent design, the buyer will have to pay a considerable amount.