Comparison Myatu F0320F vs Kugoo V1 Jilong

Nowadays, there are many types of bicycles. So, city bikes are provided for asphalt (including fixed-gear bikes and cruisers, touring and commuter bikes models can also be included here (universal version combining urban comfort and mountain passability)). Road bikes are also suitable for hard surfaces (with separate subspecies cyclocross, gravel and triathlon bikes). For rough terrain, it is better to pay attention to mountain MTB bikes (there are different types: cross-country, downhill / freeride / enduro, trail, street / dirt). A separate niche is occupied by electric bicycles, BMX and fat bikes.

— Electric bicycles. Bicycles equipped with electric motors and batteries. The method of using such equipment can be different: in some models it only helps the cyclist, reducing the effort on the pedals, in others it allows you to ride without pedalling at all, like on an electric moped (for more details, see "Operating modes"). In terms...of purpose, most of these machines are closest to city bikes, but there are exceptions - in particular, some models combine the capabilities of an electric bike and a fat bike. Electric drive provides additional convenience and reduces the cost of effort when driving; moreover, even a dead battery is not terrible for such a bike - you can continue to move in the usual way, on the pedals. On the other hand, electric bikes are much heavier than classic ones, and they are noticeably more expensive.

- Mountain (MTB). Abbreviation for MountTain Bike. In this case, two types of bicycles are included. The first is the classic “miners”, designed mainly for driving over rough terrain without specific loads typical for specialized varieties (see below). Such bicycles are built on a thick, durable frame, equipped with wide wheels, and tyres with deep treads. Many mountain models are quite suitable for driving on a flat road; of course, here they lose to road models (see below), but if you often have to drive both on the highway and off the asphalt, it is better to choose the MTB. The second variety is models that are close in characteristics to specialized ones (see below), but for one reason or another do not fit into a certain class - for example, due to heavy weight (cross-country), poor adaptability to high jumps (dirt ) and so on.

- Cross country. A type of mountain bike designed for cross-country racing. Some sections of cross-country trails are somewhat simpler than similar elements in competitions such as downhill or trials (see below), but the trails themselves are very diverse. Therefore, a bicycle of this type must combine speed, manoeuvrability, “tenacity” to the ground, and convenience on ups and downs. In practice, this is achieved by using lightweight materials for frames (aluminium, titanium, carbon, see "Frame material"), tyres with deep tread, hardtail or full suspension suspension with lockout functions (see "Suspension", "Rear suspension lockout"). ") and so on.

Downhill/freeride/enduro. A specialized type of mountain bike designed for downhill skiing. Types of such descents differ in the type of surface: downhill uses pre-prepared tracks, while more extreme freeride is carried out on complete off-road, and enduro - on the most difficult sections. However, for all varieties of bicycles, the characteristic features are common: these are wide wheels and heavyweight. The latter is due to the reinforced design: during descents, the weight does not play a decisive role, but the loads on the machine are very high, which requires increased strength and maximum reliability of all components. There is usually only one gear selector - only on the cassette (rear), respectively, there are few speeds. But the suspension on both wheels (see "Amortization") is almost mandatory.

- Trail. The trail is a specific way of riding that combines overcoming obstacles over rough terrain, conquering and descending medium peaks, road over stones and free riding on a flat road. Trail bikes have strong and heavy frames, reinforced wheels and tyres. Most of them are full-suspension with a large range of shock absorber travel (about 130 - 150 mm).

- Street / Dirt. A type of mountain bike designed for stunt riding and in some places approaching BMX. They can be designed for different styles: street acrobatics using urban elements like curbs and stairs; dirt - jumping from earthen springboards with performing tricks in the air. However, all such bicycles are characterized by common features: a small frame, one speed, as well as a minimum of depreciation or its complete absence.

- City. This class of bicycles is designed for city driving. This implies the usual movement on roads with a smooth surface, without any "extreme". City bikes are often equipped with accessories designed to increase ride comfort and enhance the bike's capabilities, such as spring saddles, racks/panniers, full-size fenders, chain guards, and so on. (see "Complete set"). For long trips and difficult conditions, city bikes are poorly suited, and therefore they can be recommended to adherents of a calm style of riding along city arteries and for pleasure riding along park paths.

— Fix. Single-speed fixed bikes were originally created as sports equipment for riding on cycle tracks. But in some subcultures of riders, they are used for the urban rhythm of travel. A distinctive feature of the nature of fixes is that the pedals of the bicycle always spin as long as the rear wheel rotates.

— Cruiser. Models with a characteristic elongated frame geometry, vertical seating, a soft comfortable saddle and a wide handlebar moved forward. When designing cruisers, they were inspired by the design of retro motorcycles. They are positioned as successful walking solutions.

— Commuter. Bicycles of this type are a cross between mountain bikes (MTB) and city bikes. On the one hand, fitness bikes provide a “sporty”, inclined landing and a large number of gears, on the other hand, there is no depreciation in the design, and additional “chips” can be provided, such as a trunk or baskets on the steering wheel, and the wheels are large (usually 28 "). This allows you to accelerate to fairly high speeds, while the bikes perfectly adapt to uneven roads and increased loads."Road" can be used to move around the city, if speed is important in such trips and the classic city bike is too slow for this, to recover and keep fit, etc.

- Touring. Bicycles designed for long-distance travel on different types of roads - both on a hard surface and on primers or rough terrain. Outwardly, they are most similar to road, gravel and cyclocross bikes, but in fact they combine the properties of mountain, road and city models. So, most tourist bikes have a more massive and durable frame than "road bikes", which allows you to more or less successfully move off paved roads. The steering wheel can be either straight or road (see "Steering wheel shape"). In addition, many models are equipped with front racks (see "Complete set") or at least mounts for them; also, the design often provides wings, a footboard and other additional equipment that provides additional comfort on long-distance bike trips.

- Road. A specialized class of bicycles designed to move on smooth roads over long distances. Road models feature a “recumbent” rider position (more forward lean) for better aerodynamics, are equipped with narrow wheels and handlebars with a characteristic curved design (see "Steering wheel model"), and do not have any shock absorbers (see "Suspension"). Thanks to all this, high speed of movement with minimal resistance is ensured - on good road surfaces, road bikes are better than any other models for long trips (suffice it to say that this type of bicycle is used in large-scale cycling races like the Tour de France). At the same time, all the advantages appear only on smooth, dry roads.

— Gravel. Bicycles that combine the features of road and mountain machines; in fact - devices designed to comfortably ride both on and off-road. The key point in this case is comfort: the “gravel road” loses to the “road” in speed, and the MTB in cross-country ability, but it is more versatile and comfortable on different types of surfaces. Note that specific criteria for gravel bikes vary from manufacturer to manufacturer. However, common features can be identified in all such models: this is a combination of a “road” steering wheel with a relatively high landing, rather thick soft tyres and disc brakes. We also note that at first glance, the “gravel roads” are similar to the cyclocross described below, but this impression is deceptive: the cyclocross is primarily a sports apparatus.

— Cyclocross. In the most general terms, this variety can be described as a modified version of road bikes (see above) with increased cross-country ability, suitable for off-road travel - grass, sand, gravel, etc. Being outwardly very similar to traditional "road bikes", cyclocrosses in at the same time, they differ from them in wider and thicker wheels and a smaller inclination of the rider when landing. In addition, cyclocross as a sport discipline provides that riders have to overcome part of the distance on foot, with a bicycle on their shoulder. In light of this, specialized bicycles for such races are also made based on the convenience of carrying on the shoulder (wide frame, traction cables hidden inside the frame). And from gravel models (see above), cyclocrosses differ primarily in that they are designed not so much for comfort as for speed and maneuverability.

For triathlon. A specialized type of road bike with a less “recumbent” rider posture and a more pronounced aerodynamic fit that allows you to maintain high speed with minimal effort. A huge bonus to aerodynamics is also given by high profile wheel rims. The weight of such bicycles is small (about 8-10 kg), they are also equipped with hydrators so that the rider can drink without changing the seat. A triathlon bike is an effective weapon to achieve your sporting goals. For everyday trips, such bikes are not customary to use at all.

— BMX. Bicycles designed to ride in the style of BMX (Bicycle Moto Cross - bicycle motocross). There are several varieties of BMX, but all of them are characterized by high loads on the structure and the performance of acrobatic stunts, which are practically inaccessible to other types of bicycles. Accordingly, BMX models have a low and very strong frame, wide wheels of small diameter (for good grip and powerful torque) and, most often, one gear (for ease of control and reliability). They can also be equipped with additional devices - for example, an axle of the front wheel extended in both directions, which the athlete uses as a step when performing tricks. Note that for normal driving on roads, BMXs are poorly suited, their purpose is acrobatics.

- Fatbike. Powerful mountain bikes designed specifically to overcome difficult obstacles such as loose snow, sand or impassable mud. First of all, they are distinguished by extremely wide tyres (see "Tyre width") and low tyre pressure, which improves grip. When riding on loose surfaces, the wheels of the bike do not fall through, and the lower pressure allows you not to get stuck in the ground.

The presence or absence of a depreciation system on a bicycle, as well as the type of this system.

— Without depreciation (rigid). In such models, the wheels are fixed directly to the rigid elements of the frame; there are no depreciation devices. Due to this, the design of the bicycle is simple, the weight is small, the cyclist feels all the features of the road topography as much as possible, and the maximum efficiency of pedaling is also achieved, which is important, for example, for road models (see "Destination"). At the same time, structural rigidity is a "double-edged sword". On the one hand, "feeling for the road" is important for BMX and some mountain models (see "Purpose"); on the other hand, the lack of shock absorption significantly increases the load on both the structure and the rider himself, leads to increased wear, fatigue and some risk of injury on rough roads.

— Depreciation of the front fork (hard tail). The most popular type of cushioning in adult bikes (see "Age Group"), especially urban and mountain types (see "Purpose"). In accordance with the name, in such bicycles, the shock-absorbing device is installed only on the front fork, while the rear wheel is rigidly fixed. The presence of a shock absorber somewhat increases the weight of the structure and complicates its maintenance, however, the advantages of such a scheme significantl...y outweigh the disadvantages: hard-tails combine good handling, “road feel” and ride comfort, including and on rough terrain.

— Rear fork. Bicycles in which only the rear wheel is damped, while the front wheel is rigidly fixed. The rear shock absorber is designed to provide additional comfort when hitting various bumps, and the absence of a front shock absorber reduces the overall cost of the machine. This option is found mainly in urban models, including electric bicycles (see "Application"); in other varieties, the use of rear shock absorption is not practical.

— Two-suspension (full suspension). Bicycles equipped with shock absorbers on both wheels — a fork in front and a special suspension in the back. Such models are as comfortable as possible for driving on rough terrain, because. They dampen the vibrations felt by the cyclist best and provide the best grip on uneven tracks. At the same time, the presence of a rear shock absorber "eats" part of the energy coming from the pedals, and you have to spend more effort to ride. To avoid this, many two-suspension bikes can be provided with front and rear suspension lockouts (see below), but full suspension complicates the design anyway, increases its weight and price. Therefore, this type of cushioning is relatively rare, mainly in certain varieties of mountain bikes (in particular, for cross-country and freeride; see "Purpose").

Front fork suspension type (if available, see "Suspension"). All shock absorption systems in bicycles work in two directions: vibration damping (damping) and impact energy absorption (cushioning). Accordingly, they have two main components: a damper and a shock absorber. Depending on the design features of these elements, the following types of depreciation are distinguished:

— Spring-elastomer. In this case, the role of a shock absorber is played by an elastic spring, and the role of a damper is played by a rod made of an elastic, well-compressible material, the so-called elastomer. This type appeared as a development of conventional spring damping systems, it is more durable, but poorly suited for low temperatures — the elasticity of the elastomer in such conditions decreases, which negatively affects the characteristics of the system.

— Spring-oil. Systems using a spring as a shock absorber and an oil cartridge as a damper. This design is somewhat more resistant to low temperatures than spring-elastomer, and in general has quite good characteristics, due to which it is quite widely used in various types of bicycles. The main disadvantage is the higher (on average) cost.

— Air-oil. Combined systems consisting of an air cylinder that acts as a shock absorber and an oil cartridge that acts as a damper. They appeared as a development of “pur...e” air systems, which had a serious drawback: even with high-quality maintenance, the seals wore out rather quickly, which could disable the shock absorber. Air-oil systems are more durable and easier to maintain, while being quite efficient and weighing little. The latter is especially valuable for cross-country (see "Purpose"), where it is required to combine depreciation with a low weight of the machine.

The presence in the design of the bicycle of a separate shock absorber under the saddle. The seatpost cushioning significantly reduces the vibration and shock felt by the rider, which is especially important when riding on uneven terrain.

The nominal diameter of the bicycle wheels. Usually, this paragraph actually indicates the size of the bicycle tyres supplied in the kit, more precisely, the outer diameter of the tyres.

Wheel diameter is traditionally indicated in inches. For bicycles of different purposes and age groups (see paragraphs above), there are certain size standards. So, adult mountain models are equipped mainly with 26 " wheels, "road" and urban ones — with a slightly larger diameter (mostly 28 "), and BMX for the most part — much smaller; children's and teens' bikes have smaller wheels than similar adults' bikes.

Other things being equal, larger tyres hold speed better and work out small bumps on the road; and relatively small wheels are more “sticky”, they provide more torque and better traction. This is the reason for the above-described difference in wheel sizes between bicycles for different purposes. Such nuances will be useful if you choose a car from several models with similar characteristics, but different wheel diameters. Here it is worth considering the features of the planned application. For example, for urban and "road" driving — on a hard surface without any special irregularities and elevation changes — it is better to choose larger wheels, and for dirt roads with ups and downs — smaller ones.

Also note that tyres are replaceable, and many bikes allow the installation of tyres of...a “non-native” size — for example, 29 "on a model with 28-inch wheels. It is also worth considering that wheels (tyres) of the same size may differ in inner (landing) diameter These nuances are described in detail in special sources.

The nominal width of the tyres supplied with the bike.

Other things being equal, a wider tyre provides a larger contact patch, which improves traction, increases flotation and makes it easier to ride on difficult surfaces like sand, mud, etc. On the other hand, this also increases resistance, as a result, wide tyres require more effort to accelerate and keeps the speed worse. So this parameter is usually chosen by manufacturers taking into account the application (see above) and other features of the bike. So, mountain and stunt (BMX) models have wide wheels ( fat bikes are even wider), city ones are narrower, and the most “elegant” are tyres on high-speed road bikes.

It is worth saying that, if necessary, “native” tyres can be replaced with wider or narrower ones. Of course, too large or too small a width is unacceptable, but there is still a certain freedom of choice here. More information about this can be found in special sources.

Light-alloy wheels of a monolithic design, cast in special moulds from aluminium, less often from titanium. Bicycles with alloy wheels are characterized by increased resistance to oncoming air flows, strength and durability, and aesthetic appeal. At the same time, alloy wheels are less resistant to side gusts of wind, have poor maintainability and are very expensive. Alloy wheels are found mainly on board city and road electric bicycles, also specialized racing bike models are equipped with alloy wheels.

The number of speeds (gears) provided for in the design of the bicycle. Each transfer has its own so-called gear ratio — in this case it can be described as the number of revolutions that the driven gear (rear, on the wheel) makes in one revolution of the leading gear (associated with the pedals).

Different gear ratios will be optimal for different conditions: for example, high gears provide good speed, but are poorly suited for overcoming obstacles, because. the effort on the pedals increases significantly and the frequency of their rotation decreases. It has been scientifically proven that a cyclist develops maximum power at a cadence of about 80-100 rpm. Thus, the presence in the bike of several speeds allows you to optimally adjust it to different driving modes and features of the tracks in order to provide optimal pedaling force and frequency of their rotation. For example, on smooth asphalt it is best to drive in a high gear, and when overcoming a rise or entering a dirt road, you can lower it in order to effectively overcome resistance.

The number of gears in classic systems is directly related to the number of stars of the system (on the bottom bracket with pedals) and the cassette (on the rear wheel); it can be obtained by multiplying two numbers — for example, 3 stars of the system and 6 on the cassette give 18 gears. However, there is also the so-called planetary hubs — there are stars one at a time, and gear shifting is carried out by a mec...hanism built into the rear hub.

Note that the optimal number of gears depends on the purpose of the bike (see above), and it is not always necessary to have several of them. So, in mountain models, depending on specialization, there can be from 8 to 30 gears, in road ones — within 20-30, and some inexpensive city bikes and most BMXs do not have a gear shift system at all.

The number of stars (gears) of different sizes in a bicycle cassette. A cassette is a part of the rear hub that interacts directly with the chain, in other words, a gear or a set of gears mounted on the hub. In classical gear shifting systems, the number of gears directly depends on the number of stars in the cassette (for more details, see "Speeds"); a single chainring is used either in single speed bikes or in planetary hubs (see System Stars for more on these).